Hydraulic Technical Library

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic maintenance tips, application formulas and guidelines, conversions and other technical data designed to help you solve your hydraulic problems.

Warning! High pressure fluid is present in operational hydraulic systems. Fluids under high pressure are dangerous and can cause serious injury or death. Do not make modifications, repairs or adjustments to any hydraulic system unless you are competent or working under competent supervision. If in doubt consult a qualified technician or engineer.

MAINTENANCE AND TROUBLESHOOTING Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

Anatomy of a hydraulic pump failure Hydraulic cylinder failure caused by the diesel effect Hydraulic ram leak caused by operator error The value of the humble hydraulic symbol Controlling decompression in hydraulic press circuits Hydraulic cylinder rods turn black Determining hydraulic pump condition using volumetric efficiency Hydraulic system overheating problems Hydraulic cylinders - checking rod straightness Hydraulic pump life cut short by particle contamination Hydraulic press failure illustrates the importance of scheduling change-outs

http://www.hydraulicsupermarket.com/technical.html (1 of 3) [5/10/2004 7:47:09 PM]

Hydraulic Tutorials

Hydraulic motors - how dry starts damage them Hydraulic valves - preventing cavitation damage Hydraulic hose - failure costs and prevention Hydraulic system troubleshooting - check the easy things first Proactive maintenance for hydraulic cylinders Hydraulic fitting selection the key to leak-free hydraulic plumbing Common causes of hydraulic seal failure in cylinders Hydraulic filters that do more harm than good - Part 1 Hydraulic filters that do more harm than good - Part 2 Hydraulic filters that do more harm than good - Part 3 Hydraulic power unit problem highlights the value of hydraulic pump testing Adding hydraulic oil - without the dirt Hydraulic fluid - getting the viscosity right High hydraulic fluid temperature - how it causes premature failures Biodegradable hydraulic fluid - its application and use Hydrostatic transmissions - making sense of case drain flow - Part 1 Hydrostatic transmissions - making sense of case drain flow - Part 2 Hydrostatic transmissions - making sense of case drain flow - Part 3 Temperature shock of hydraulic components and how to avoid it Configuring mobile hydraulic valves using power beyond The true cost of hydraulic oil leaks El Valor de un Sencillo Símbolo Hidráulico

APPLICATION GUIDELINES AND FORMULAS Hydraulic accumulators Hydraulic cooling and heating Hydraulic cylinders Hydraulic drive calculations for vehicles Hydraulic filters Hydraulic fluids Hydraulic pumps and motors Hydraulic reservoirs Hydraulic winch drive calculations Orifices in hydraulic systems Velocity and pressure drop in hydraulic pipes and hoses

http://www.hydraulicsupermarket.com/technical.html (2 of 3) [5/10/2004 7:47:09 PM]

Hydraulic Tutorials

TECHNICAL REFERENCE DATA Conversion factor tables Hydraulic fitting thread data Hydraulic gear pump displacement calculation Hydraulic seal sizes for SAE flanges and threaded adaptors Hydraulic symbols Hydraulic vane pump displacement calculation Pressure rating of hydraulic tubing SAE hydraulic hose specifications SAE hydraulic port flange dimensions SAE hydraulic pump and motor mounting flange and shaft dimensions Your use of this site acknowledges acceptance of our terms and conditions of use.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical.html (3 of 3) [5/10/2004 7:47:09 PM]

Hydraulic Cylinder, Hydraulic Pump, Hydraulic Motor, Hydraulic Valve, Product Data - Hydraulic Supermarket

Show me how to:

choose from list

Go

hydraulic product library

Click on the links below to download product literature from leading hydraulic and pneumatic component manufacturers, and browse related sites.

Hydraulics ●

●

●

●

●

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to

●

●

claim a free subscription. ●

●

●

●

●

●

●

●

●

Barnes AC/DC power units, gear pumps, motors and flow dividers. Bosch Gear and vane pumps, accumulators, cylinders, valves and electronics. Brand Hand pumps, directional and flow controls and electronics. Brueninghaus Axial piston pumps and motors. Calzoni Low speed, high torque radial piston hydraulic motors. Casappa Hydraulic gear pumps and motors. Char-Lynn (Eaton) Orbital motors and steering units. Command Controls Hydraulic cartridge valves and manifolds. Commercial (Parker) Gear pumps and motors. Cross Gear pumps, directional valves, cylinders and accumulators. Danfoss Orbital motors and steering units, valves and electronics. Denison Piston and vane pumps and motors, valves and electronics. Des-Case Desiccant tank breathers. Dinamic Oil Orbital motors, radial piston motors and hydraulic winches. Donaldson Hydraulic filters Dynex Piston pumps, vane motors and valves.

http://www.hydraulicsupermarket.com/products.html (1 of 6) [5/10/2004 7:47:20 PM]

Hydraulic Cylinder, Hydraulic Pump, Hydraulic Motor, Hydraulic Valve, Product Data - Hydraulic Supermarket ●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Eaton Piston pumps and motors. Edi System Cartridge valves. Enerpac Hydraulic tools, high pressure cylinders, hand pumps and power units. EPCO Products Port entry plugs and hydraulic fittings that are guaranteed not to leak. Eppensteiner Filters. Fairey Arlon Filters. Fawcett Christie Accumulators. Flender Hydrex (now Hagglunds Hydrex) Radial piston motors Gresen (Parker) Gear pumps and motors, valves, filters and electronics. Hagglunds Radial piston motors. Haldex AC/DC hydraulic power units, gear pumps, motors and flow dividers. HAWE Radial piston pumps, valves and accumulators. HUSCO Directional control valves. HYDAC Accumulators, filters, heat exchangers and accessories. HydraForce Cartridge valves. Hydromatik Piston pumps and motors. Hydrostar Radial piston motors Hydrotechnik Flowmeters, pressure gauges, pressure transducers, dataloggers and other test equipment. Integrated Cartridge valves. Intermot Radial piston motors. Internormen Filters and contamination testing equipment Kawasaki Axial piston pumps and motors, radial piston motors and valves. Kracht Gear pumps and motors, valves, and electronics. Lake Monitors Flowmeters and hydraulic test equipment. Lamborghini Oleodinamica Gear pumps, motors and flow dividers, and control valves. LHA Filters, reservoirs and accessories.

http://www.hydraulicsupermarket.com/products.html (2 of 6) [5/10/2004 7:47:20 PM]

Hydraulic Cylinder, Hydraulic Pump, Hydraulic Motor, Hydraulic Valve, Product Data - Hydraulic Supermarket ●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Linde Axial piston pumps and motors. Marzocchi High pressure hydraulic gear pumps and motors. MICO Brake systems. MiniBooster Hydraulic pressure intensifiers. Monarch DC hydraulic power units and systems Moog (Bosch Racine) Radial piston pumps (RKP) Moog Servo-valves. Northman Hydraulic vane pumps and valves. Oil Control Cartridge valves. Oilgear Piston pumps and motors, valves and electronics. Oiltech Heat exchangers. Olaer Accumulators. Parker Pumps, motors, cylinders, valves, filters and accessories. Pedro Roquet Hydraulic gear pumps and motors, valves, cylinders and AC/DC mini power-packs. Permco Gear pumps, motors and flow dividers. Poclain Radial piston motors, pumps and valves. Pradifa Hydraulic and pneumatic seals. PZB High pressure gear pumps. Rexroth Piston pumps and motors, valves, cylinders and accessories. Rineer Low speed, high torque vane hydraulic motors Rotary Power Axial piston hydraulic pumps and motors, and radial piston hydraulic motors. SAI Radial piston motors. Salami Gear pumps and motors. SAM Orbital motors and steering units, and axial piston pumps and motors. Sauer Danfoss Piston pumps and motors, gear pumps and electronics. Scanwill Fluid Power

http://www.hydraulicsupermarket.com/products.html (3 of 6) [5/10/2004 7:47:20 PM]

Hydraulic Cylinder, Hydraulic Pump, Hydraulic Motor, Hydraulic Valve, Product Data - Hydraulic Supermarket

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Pressure intensifiers and hydraulic cylinder regeneration valves. Schroeder Industries Hydraulic filters Seal Saver Protective cover for hydraulic cylinders - increases cylinder rod and seal life and reduces contaminant ingress. Simplex Hydraulic tools, high pressure cylinders, valves and power units. Simrit Radial shaft seals and hydraulic seals. SOK Low speed, high torque motors of circulating cam construction. Staffa (Kawasaki) Radial piston motors. Stauff Filters, accessories and hydraulic test equipment. Sterling Cartridge valves. Sundstrand Piston pumps and motors, gear pumps and electronics. Sun Cartridge valves. Tokimec Piston and vane pumps, vane motors and valves. Tyrone (Parker) Gear pumps and motors. Vickers (Eaton) Pumps, motors, cylinders, valves, filters and accessories. VOAC (Volvo - Atlas Copco) Parker Piston pumps and motors, orbital motors and valves. Voith High pressure gear pumps. Von Ruden Orbital motors and steering units, vane motors and brake units. Wandfluh Cetop valves and cartridge valves. Webster Instruments (Webtec) Hydraulic test equipment, gear pumps and motors, cylinders and valves. White Orbital motors. Yuken Piston and vane pumps and valves.

Pneumatics ●

●

●

●

Camozzi Cylinders, valves, fittings and accessories. Domnick Hunter Compressed air filters Festo Actuators, valves, air preparation, fittings and accessories. Norgren Actuators, valves, air preparation, fittings and accessories.

http://www.hydraulicsupermarket.com/products.html (4 of 6) [5/10/2004 7:47:20 PM]

Hydraulic Cylinder, Hydraulic Pump, Hydraulic Motor, Hydraulic Valve, Product Data - Hydraulic Supermarket ●

●

●

●

Parker Actuators, valves, air preparation and accessories. Rexroth Mecman Actuators, valves, air preparation and accessories. Ross Valves, air preparation and accessories. SMC Actuators, valves, air preparation and accessories.

Related sites ●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

@ptitudeXchange Web-enabled, knowledge source for asset maintenance and reliabilityrelated issues. Content comes in the form of articles, reports, whitepapers, interactive services, training primers, and more. Part of it can be accessed for free after registration, while other parts require a subscription. All About Pumps Operating principles of over 70 different types of pumps, including hydraulic pumps, are animated and explained. Association for Facilities Engineering Largest, dedicated network in the facility, maintenance, and plant operations professions. Bortech BoreWelders Innovative, automatic welding system for repairing hydraulic cylinder eyes. Business Industrial Network Eliminates unnecessary equipment downtime by providing online engineering & maintenance. FastMaint CMMS An affordable maintenance management solution. Hydraulic Engineering Educational animations of hydraulic components and fluid power concepts. IDCON Education, training and implementation of better reliability practices. Insider Secrets to Hydraulics Valuable technical information for anyone with an interest in hydraulics. Maintenance Resources Plant engineering, maintenance and reliability resources. Maintenance World Maintenance and reliability article library. MaintSmart Software Maintenance management software – CMMS with reliability analysis. Plant Maintenance Resource Center Maintenance articles, listings of maintenance consultants, CMMS and maintenance software vendors, maintenance conferences and more... Reliability Center Reliability consulting services, training programs, software products and resources for business, industry, government and healthcare organizations. RSG Technologies Dry ice blasting equipment from Icesonic; Industrial cleaning technology that supports cleaning in place (CIP), minimizing waste disposal and reducing equipment downtime.

http://www.hydraulicsupermarket.com/products.html (5 of 6) [5/10/2004 7:47:20 PM]

Hydraulic Cylinder, Hydraulic Pump, Hydraulic Motor, Hydraulic Valve, Product Data - Hydraulic Supermarket ●

●

●

Surplus Center Surplus hydraulic and power transmission components. Total Productive Maintenance Articles on lean manufacturing, root cause, reliability and much more... Used Heavy Equipment Marketplace for used hydraulic agricultural, construction, forestry and mining equipment from major manufacturers including Caterpillar, Case, JCB, John Deere, Komatsu, Roadtec, Terex and many others.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/products.html (6 of 6) [5/10/2004 7:47:20 PM]

Hydraulic Surplus

Show me how to:

choose from list

Go

hydraulic surplus marketplace VIEW MARKETPLACE | LIST YOUR ITEMS | TERMS OF USE

Welcome to Hydraulic Supermarket's dedicated Marketplace for the trading of surplus hydraulic and pneumatic components. All businesses are conscious of the need to improve their inventory management techniques. It doesn't matter whether you are an operator of hydraulic equipment or a distributor of hydraulic components, even with best-practice inventory management you can still get caught holding obsolete spare parts or surplus inventory, as Michael Hall, President of Hydratorque in Sydney, Australia explains: "The killer of all hydraulic companies is 'dead' or excess stock. Every company I know has accumulated hundreds of thousands of dollars worth of excess inventory. Every time an overseas supplier changes their distribution, I get stuck with at least $100,000 worth."

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to

What can be done about this problem? Hydraulic Supermarket offers a solution by providing a Marketplace where sellers can list their surplus hydraulic and pneumatic inventory for potential buyers to browse and make offers. Superseded, difficult to find, or high value hydraulic: pumps, motors, cylinders and valves, whether new, used or rebuilt, are in most cases saleable commodities.

claim a free subscription.

Hydraulic Supermarket's on-line Marketplace facilitates trade in surplus hydraulic components by enabling: ●

●

Sellers of surplus components to submit details of items available for sale for inclusion in our Marketplace database. Submitted items can be removed from the database by the seller when sold or if withdrawn from sale at any time. Buyers to browse components available for sale and submit offers to sellers. The method of sale is by private treaty directly between buyer and seller. Before using the Marketplace please read our terms and conditions of use.

During our beta phase there is no commission charged for buying or selling surplus components through Hydraulic Supermarket. ● ●

View components for sale List your components for sale

http://www.hydraulicsupermarket.com/market.html (1 of 2) [5/10/2004 7:47:24 PM]

Hydraulic Surplus ●

Terms and Conditions of Use

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/market.html (2 of 2) [5/10/2004 7:47:24 PM]

Hydraulic System Design

Show me how to:

choose from list

Go

consult an expert

Hydraulic Supermarket's expert engineers have a minimum of ten years experience in all facets of hydraulic fluid power system design for mining, oil and gas, marine and industrial applications. Fill in the form below to send us details of your system's requirements, and we'll get back to you with a fixed price to design a system that meets your requirements, complete with CAD drawings. Note: if your inquiry is not related to design work, then please go to our contact us page. Fields in red are required; others are optional. Business Name: Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

Street Address: City: Zip Code Country: Telephone: Facsimile: E-mail Address: First Name:

http://www.hydraulicsupermarket.com/consult.html (1 of 3) [5/10/2004 7:47:27 PM]

Hydraulic System Design

Last Name: Nearest Airport: Nearest Seaport: Application description If possible, specify output torque or force and rpm or speed required from all motors and cylinders

Installation location: Ambient air temperature: Prime mover type: Additional information

Send Inquiry

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

http://www.hydraulicsupermarket.com/consult.html (2 of 3) [5/10/2004 7:47:27 PM]

Search

Hydraulic System Design

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/consult.html (3 of 3) [5/10/2004 7:47:27 PM]

Hydraulic Supermarket about us

Show me how to:

choose from list

Go

about us The Hydraulic Fluid Power Marketplace and Resource Center Hydraulic Supermarket is an independent Marketplace and resource center for everyone who has an interest in hydraulics. If you own, operate, design, build, maintain, or repair hydraulic equipment, then you will find the resources available at HydraulicSupermarket.com invaluable, as Michael H. Robson, Training Manager Product Support at Hitachi Construction Machinery (America) Corporation explains: "I am extremely impressed with (HydraulicSupermarket.com) and its content. Your information is extremely valuable to anyone involved in hydraulics. The content is complete, accurate and informative. This is one of the best sites I have ever seen." Glitz matters to some, but it is not a substitute for content. There are many great Web sites that look great but just don't give you what you need, as Timothy Andres testifies: "Yours is the only site I saved in my favorites, I have searched the Internet for other hydraulic sites but they do not have the data that you do. (HydraulicSupermarket.com) is the only site out of 50 that I have searched that could help me with the technical data and understanding of hydraulics." Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

Since going online in November 2000, Hydraulic Supermarket has strived to provide the highest level of customer service. David La Noue is one satisfied customer who believes we set the benchmark in customer support: "Thank you for the information. Yours is the only response received from many inquiries sent to other companies and exchanges. You should be commended on your attention to customer satisfaction. Please feel free to forward this email as a recommendation to your management." HydraulicSupermarket.com is designed to help you solve your hydraulic problems. You can use this site to: ●

●

buy and sell surplus new, used and rebuilt hydraulic components in our dedicated Marketplace. develop your own solutions to technical and application problems with the help of our extensive Technical Library.

http://www.hydraulicsupermarket.com/about.html (1 of 2) [5/10/2004 7:47:31 PM]

Hydraulic Supermarket about us ●

●

browse product data from leading hydraulic component manufacturers in our comprehehsive Product Library. consult our expert engineers, who can design solutions to your hydraulic application problems.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/about.html (2 of 2) [5/10/2004 7:47:31 PM]

Hydraulic Supermarket contact us

Show me how to:

Go

choose from list

contact us E-mail Address (required): First Name (required): Last Name (required): Organization: Message

Send Message

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

http://www.hydraulicsupermarket.com/contact.html (1 of 2) [5/10/2004 7:47:34 PM]

Search

Hydraulic Supermarket contact us

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/contact.html (2 of 2) [5/10/2004 7:47:34 PM]

Hydraulic Fluid Power Marketplace And Resource Center

Show me how to:

Go

choose from list

Use our Technical Library to help you solve your hydraulic problems. Here you will find practical information on hydraulic maintenance, troubleshooting and repair, formulas, conversions and more... Figured out what you need but not sure what is available? Browse product literature from leading hydraulic component manufacturers in our Product Library.

Need a rare or superseded hydraulic cylinder, pump, motor or valve, or want to save money on a replacement component? Check out our Marketplace for surplus new, used and rebuilt hydraulic components. Don't have the time or inclination to do it yourself? Our expert engineers can design and specify a hydraulic system to your requirements.

Advertising | Link To Us | About Us | Contact Us | Newsletter | Site Map Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/index.html [5/10/2004 7:47:37 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic accumulators Hydraulic accumulators store fluid under pressure and can serve a number functions within a hydraulic system. The most common type of accumulator employed in modern hydraulic systems is the nitrogen gas loaded type. The following document explains how to calculate the accumulator volume and gas pre-charge pressure required in various applications. File size: 14 kB Download time: ~ 30 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

http://www.hydraulicsupermarket.com/technical3.html (1 of 2) [5/10/2004 7:47:40 PM]

Hydraulic Tutorials

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical3.html (2 of 2) [5/10/2004 7:47:40 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic cooling and heating Heating of the hydraulic fluid in operation is caused by inefficiencies. Inefficiencies result in losses of input power, which are converted to heat. The following document explains how to determine: the size of heat exchanger required to remove operational heat load; the amount of heat dissipated via the reservoir and the power of a heating element required to maintain or raise reservoir fluid temperature in low ambient conditions. File size: 17 kB Download time: ~ 30 seconds Download document Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

http://www.hydraulicsupermarket.com/technical4.html (1 of 2) [5/10/2004 7:47:44 PM]

Hydraulic Tutorials

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical4.html (2 of 2) [5/10/2004 7:47:44 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic cylinders Cylinders convert fluid power into linear force and motion. The linear force generated by a hydraulic cylinder is a product of system pressure and effective area, minus inefficiencies (losses). When sizing a hydraulic cylinder for a specific application the relationships between pressure, area, displacement volume, flow, speed, and the influence of inefficiencies must be considered. File size: 268 kB Download time: ~ 40 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

http://www.hydraulicsupermarket.com/technical5.html (1 of 2) [5/10/2004 7:47:48 PM]

Hydraulic Tutorials

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical5.html (2 of 2) [5/10/2004 7:47:48 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic drive calculations for vehicles The following document explains how to calculate the output torque and speed required from a hydraulic drive (hydrostatic transmission) to propel a vehicle. File size: 15 kB Download time: ~ 20 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical11.html (1 of 2) [5/10/2004 7:47:51 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical11.html (2 of 2) [5/10/2004 7:47:51 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic filters Filters are an essential component of every hydraulic system. Their function is to remove particle contaminants from the hydraulic fluid, which reduce the service life of system components through abrasive wear. The following document contains practical information on the rating, sizing and selection of hydraulic filters, fluid cleanliness standards and fluid condition analysis. File size: 18 kB Download time: ~ 30 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

http://www.hydraulicsupermarket.com/technical6.html (1 of 2) [5/10/2004 7:47:54 PM]

Hydraulic Tutorials

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical6.html (2 of 2) [5/10/2004 7:47:54 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic fluids When selecting a hydraulic fluid for a particular application a number of properties may need to be considered. The most important of these properties is typically kinematic viscosity. The following document contains practical information on viscosity and bulk modulus, including a temperature/viscosity diagram for ISO hydraulic oils; and a formula for calculating compressibility of hydrocarbon based fluids. File size: 285 kB Download time: ~ 3 minutes Download document Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

http://www.hydraulicsupermarket.com/technical7.html (1 of 2) [5/10/2004 7:47:56 PM]

Hydraulic Tutorials

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical7.html (2 of 2) [5/10/2004 7:47:56 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic pumps and motors Useful power in a hydraulic system is a product of flow and pressure, minus inefficiencies. When selecting a hydraulic pump and/or motor for a specific application the relationships between flow, displacement, speed, torque and pressure, and the influence of inefficiencies must be considered. The following guidelines and calculations can be applied to all rotary drives. File size: 19 kB Download time: ~ 20 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

http://www.hydraulicsupermarket.com/technical9.html (1 of 2) [5/10/2004 7:47:59 PM]

Hydraulic Tutorials

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical9.html (2 of 2) [5/10/2004 7:47:59 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic reservoirs The reservoir or tank carries out a number of important functions in the hydraulic system. The following document contains practical information on hydraulic reservoirs: fluid volume, construction and installation. File size: 11 kB Download time: ~ 20 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical10.html (1 of 2) [5/10/2004 7:48:02 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical10.html (2 of 2) [5/10/2004 7:48:02 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic winch drive calculations The following document explains how to calculate the output torque and speed required from a hydraulic motor (hydrostatic transmission) to drive a winch. File size: 12 kB Download time: ~ 20 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical13.html (1 of 2) [5/10/2004 7:48:05 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical13.html (2 of 2) [5/10/2004 7:48:05 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Orifices in hydraulic systems Orifices are used in hydraulic circuits to restrict flow. The following document explains how to calculate: orifice diameter required to pass a desired flow at a specified pressure; flow rate through an orifice of a known diameter at a specified pressure; and pressure drop across an orifice of a known diameter at a specified flow rate. File size: 6 kB Download time: ~ 20 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

http://www.hydraulicsupermarket.com/technical8.html (1 of 2) [5/10/2004 7:48:08 PM]

Hydraulic Tutorials

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical8.html (2 of 2) [5/10/2004 7:48:08 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Velocity and pressure drop in hydraulic pipes and hoses Friction between the hydraulic fluid flowing through a conductor (pipe, tube or hose) and its inside wall causes losses, which are quantified as pressure drop. Pressure drop is influenced by a number of factors including the velocity of the fluid through the conductor, which is dependent on flow rate and cross sectional area. Velocity and pressure drop in conductors are important considerations for fluid power designers especially in systems where long pipe or hose runs are necessary. The following document contains practical information that includes recommended fluid velocities for hydraulic systems, flow/velocity nomograms and formulas for calculating velocity and pressure drop. File size: 350 kB Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to

Download time: ~ 40 seconds Download document

claim a free subscription.

http://www.hydraulicsupermarket.com/technical12.html (1 of 2) [5/10/2004 7:48:11 PM]

Hydraulic Tutorials

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical12.html (2 of 2) [5/10/2004 7:48:11 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Conversion factor tables Conversion factors and symbols for imperial and metric units commonly used by hydraulic fluid power designers. File size: 17 kB Download time: ~ 30 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical15.html (1 of 2) [5/10/2004 7:48:15 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical15.html (2 of 2) [5/10/2004 7:48:15 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic fitting thread data The following tables collate dash size, thread dimensions and TPI, for commonly used hydraulic fittings: BSP, DIN, JIC, UNO, NPT, ORFS and SAE. File size: 13 kB Download time: ~ 30 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical14.html (1 of 2) [5/10/2004 7:48:18 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical14.html (2 of 2) [5/10/2004 7:48:18 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic gear pump displacement calculation The volumetric displacement of a hydraulic gear pump or motor can be approximated by measurement of the internal parts and substituting the values in the following formula: File size: 126 kB Download time: ~ 60 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical16.html (1 of 2) [5/10/2004 7:48:20 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical16.html (2 of 2) [5/10/2004 7:48:20 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic seal sizes for SAE flanges and threaded adaptors The following tables list seal (o-ring) sizes for Unified National O-Ring (UNO) threaded adaptors (SAE J192) and SAE port flanges (SAE J518). File size: 20 kB Download time: ~ 30 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical26.html (1 of 2) [5/10/2004 7:48:23 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical26.html (2 of 2) [5/10/2004 7:48:23 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic symbols This document illustrates commonly used International Organization for Standardization (ISO) hydraulic symbols to assist in interpretation of hydraulic schematic circuit drawings. File size: 1244 kB Download time: ~ 90 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical19.html (1 of 2) [5/10/2004 7:48:26 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical19.html (2 of 2) [5/10/2004 7:48:26 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Hydraulic vane pump displacement calculation The volumetric displacement of a hydraulic vane pump or motor can be approximated by measurement of the internal parts and substituting the values in the following formula: File size: 22 kB Download time: ~ 40 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical22.html (1 of 2) [5/10/2004 7:48:29 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical22.html (2 of 2) [5/10/2004 7:48:29 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

Pressure rating of hydraulic tubing There a three commonly used formulas for calculating the burst pressure of seamless hydraulic tubing, Barlow’s formula, Boardman’s formula and Lame’s formula. Once the theoretical burst pressure of the tube has been calculated using one of these formulas, working pressure is calculated by dividing the burst pressure by a desired factor of safety. This document contains a table of reference working pressures in psi of seamless steel tube calculated using Barlow’s formula, based on a minimum ultimate tensile strength of 50,000 psi and a design safety factor of 4:1. File size: 18 kB Download time: ~ 40 seconds Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to

Download document

claim a free subscription.

http://www.hydraulicsupermarket.com/technical21.html (1 of 2) [5/10/2004 7:48:32 PM]

Hydraulic Tutorials

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical21.html (2 of 2) [5/10/2004 7:48:32 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

SAE hydraulic hose specifications Hydraulic hose has a finite service life, which can be reduced by many factors including: frequency and amplitude of pressure fluctuations, exposing the hose to pressure spikes above the maximum recommended working pressure, operation outside of the recommended temperature range, flexing the hose to less than the minimum specified bend radius and twisting, pulling, kinking, crushing or abrasion of the hose. The following document contains construction details and performance data, including pressure and temperature ratings and allowable bend radius, for SAE hydraulic hose. File size: 22 kB Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to

Download time: ~ 40 seconds Download document

claim a free subscription.

http://www.hydraulicsupermarket.com/technical20.html (1 of 2) [5/10/2004 7:48:35 PM]

Hydraulic Tutorials

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical20.html (2 of 2) [5/10/2004 7:48:35 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

SAE hydraulic port flange dimensions The following tables collate dimensions, bolt sizes and pressure ratings for SAE Code 61 and Code 62 port flanges. File size: 49 kB Download time: ~ 90 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical17.html (1 of 2) [5/10/2004 7:48:38 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical17.html (2 of 2) [5/10/2004 7:48:38 PM]

Hydraulic Tutorials

Show me how to:

choose from list

Go

hydraulic technical library

SAE hydraulic pump and motor mounting flange and shaft dimensions The following tables contain dimensional information for SAE 2 bolt and 4 bolt hydraulic mounting flanges and SAE keyed and splined shafts. File size: 73 kB Download time: ~ 70 seconds Download document

Keep abreast of hydraulic maintenance issues with Machinery Lubrication magazine. Click here to claim a free subscription.

"This book has the potential to save many organizations lots of money. It should be on the bookshelf of every engineer, supervisor, planner and technician that deals with hydraulic equipment... it's worth its weight in gold." Find out more Alexander (Sandy) Dunn Plant Maintenance Resource Center

Advertising | Link To Us | About Us | Contact Us | Newsletter | Home

http://www.hydraulicsupermarket.com/technical18.html (1 of 2) [5/10/2004 7:48:42 PM]

Hydraulic Tutorials

Search the site:

Search

HydraulicSupermarket.com email: [email protected] Terms of Use | Privacy Statement

http://www.hydraulicsupermarket.com/technical18.html (2 of 2) [5/10/2004 7:48:42 PM]

Hydraulic Pump, Hydraulic Pump Failure

Anatomy of a hydraulic pump failure I was asked recently to give a second opinion on the cause of failure of an axial piston pump. The hydraulic pump had failed after a short period in service and my client had pursued a warranty claim with the manufacturer. The manufacturer rejected the warranty claim on the basis that the failure had been caused by contamination of the hydraulic fluid. The foundation for this assessment was scoring damage to the valve plate (Figure 1).

Figure 1. Scoring damage to valve plate

How does contamination cause this type of damage to a hydraulic pump? When hydraulic fluid is contaminated with hard particles that are the same size as the clearance between two lubricated surfaces, a process known as three-body abrasion occurs. Three-body abrasion results in scoring and heavy wear of sliding surfaces (Figure 2).

http://www.insidersecretstohydraulics.com/hydraulic-pump-failure.html (1 of 3) [5/10/2004 7:58:42 PM]

Hydraulic Pump, Hydraulic Pump Failure

Figure 2. The process of three-body abrasion

What other explanations are there for this type of damage? In axial piston designs, the cylinder barrel is hydrostatically loaded against the valve plate. The higher the operating pressure, the higher the hydrostatic force holding the cylinder barrel and valve plate in contact. However, if operating pressure exceeds design limits or if the valve plate is not in proper contact with the cylinder barrel, the cylinder barrel separates from the valve plate. Once separation occurs, the lubricating film is lost, the two surfaces come into contact and a process known as two-body abrasion occurs. A major clue that the damage to the valve plate was not caused by contamination in this case, is the pattern of wear. Notice that the scoring (bright areas) is confined to the inner and outer edges of the sliding surface of the valve plate (see Figure 1). If the scoring had been caused by three-body abrasion, the damage would be more evenly distributed across the entire surface, with the areas between the pressure kidneys at the top of the picture, likely to exhibit the heaviest damage. The pattern of wear on the valve plate is consistent with two-body abrasion resulting from uneven contact between the valve plate and cylinder barrel, caused by warping of the valve plate and/or separation. Examination of the sliding surface of the cylinder barrel (Figure 3) supports this assessment. Notice that the scoring of the cylinder barrel is heaviest top right of the picture and lightest bottom left. Examination of the head of the hydraulic pump also revealed uneven contact between the valve plate and head.

http://www.insidersecretstohydraulics.com/hydraulic-pump-failure.html (2 of 3) [5/10/2004 7:58:42 PM]

Hydraulic Pump, Hydraulic Pump Failure

Figure 3. Scoring damage to cylinder barrel

Root cause of failure Although the valve plate was flat, its locating dowel was holding it off the head on one side (center right of Figure 1). This in turn was causing the valve plate to be tilted against the cylinder barrel, resulting in uneven loading, separation and two-body abrasion of the two surfaces. The root cause of this hydraulic pump failure was not contamination; but rather improper assembly at the factory.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-pump-failure.html (3 of 3) [5/10/2004 7:58:42 PM]

Hydraulic Cylinder, Hydraulic Cylinders

Hydraulic cylinder failure caused by the 'diesel effect' I was recently engaged by a client to conduct failure analysis on a large (and expensive) hydraulic cylinder off an excavator. This cylinder had been changed-out due to leaking rod seals after achieving only half of its expected service life. Inspection revealed that apart from the rod seals, which had failed as a result of the 'diesel effect', the other parts of the hydraulic cylinder were in serviceable condition.

What is the 'diesel effect'? The diesel effect occurs in a hydraulic cylinder when air is drawn past the rod seals, mixes with the hydraulic fluid and explodes when pressurized.

How does this affect a hydraulic cylinder? When a double-acting hydraulic cylinder retracts under the weight of its load, the volume of fluid being demanded by the rod side of the cylinder can exceed the volume of fluid being supplied by the pump. When this happens, a negative pressure develops in the rod side of the hydraulic cylinder, which usually results in air being drawn into the cylinder past its rod seals. This occurs because most rod seals are designed keep high-pressure fluid in and are not designed to keep air out. The result of this is aeration - the mixing of air with the hydraulic fluid. Aeration causes damage through loss of lubrication and overheating, and when a mixture of air and oil is compressed it can explode, damaging the hydraulic cylinder and burning its seals. As you have probably gathered, the term 'diesel effect' is a reference to the combustion process in a diesel engine. In the example described above, the cause of the aeration was a faulty 'float' valve. The function of a float valve on a hydraulic excavator is to allow the boom or arm to be lowered rapidly under its own weight. When activated, this valve connects the ports of the hydraulic cylinder together allowing it to retract under the weight of the boom or arm. The fluid displaced from the http://www.insidersecretstohydraulics.com/hydraulic-cylinder.html (1 of 2) [5/10/2004 7:58:44 PM]

Hydraulic Cylinder, Hydraulic Cylinders

piston side of the cylinder is directed with priority to the rod side, before any excess volume is returned to the hydraulic reservoir. An orifice controls the speed with which the cylinder retracts. If this valve malfunctions or is set incorrectly, a negative pressure can develop on the rod side of the hydraulic cylinder, causing air to be drawn past the rod seals, leading to failure of the cylinder.

How can this type of failure be prevented? This example highlights the importance of checking the operation and adjustment of circuit protection devices at regular intervals. As in this case, if the faulty float valve had been identified early enough, the failure of this hydraulic cylinder and the significant expense of its repair could have been prevented.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-cylinder.html (2 of 2) [5/10/2004 7:58:44 PM]

Hydraulic Ram, Hydraulic Lift

Hydraulic ram leak caused by operator error A client recently asked me to explain a seal failure on a hydraulic ram. The ram had been removed from a hydraulic lift due to a leaking rod seal, but upon inspection, both the rod seal and the surface of the rod were found to be in serviceable condition.

What is a hydraulic ram? A hydraulic ram is a single-acting cylinder in which fluid pressure acts on the crosssection of the rod i.e. it has no piston (Figure 1).

http://www.insidersecretstohydraulics.com/hydraulic-ram.html (1 of 3) [5/10/2004 7:58:52 PM]

Hydraulic Ram, Hydraulic Lift

Figure 1. Hydraulic ram sectional view showing U-cup seal profile.

Failure investigation Because inspection of the rod seal (U-cup type) and the rod's surface didn't reveal any obvious cause of failure, I asked the operator to describe the nature of the leak. He explained that during his morning inspections he had noticed that there was always a trickle of hydraulic fluid down the side of the ram. Further investigation revealed that the current operator had only been assigned to the machine several weeks earlier. So I asked the operator to explain how he left the hydraulic lift at night. He advised that after shutting down he always relaxed the hydraulics (released the load off the hydraulic ram). This revealed the most likely explanation for the nuisance leak.

Seal energization To seal effectively, a U-cup seal relies on hydraulic fluid pressure to energize the lips of the seal against the rod and seal groove (Figure 1 inset). Releasing the loadinduced pressure from the hydraulic ram after shutdown effectively de-energizes the seal. Once the seal is de-energized, a gradual increase in the volume of fluid in the ram due to thermal expansion can result in fluid leaking past the seal. This gradual loss of fluid prevents development of sufficient pressure to effectively energize the seal, so the leak continues until the temperature, and therefore volume, of the fluid in the ram stabilizes.

Root cause of failure I advised my client that the practice of taking the load of the hydraulic ram after shutdown was the most likely cause of the leak. This being the case, there were two possible solutions. Discontinue the practice or change the seal profile to an energized U-cup (a U-cup that has an O-ring fitted in the 'U' to pre-energize the lips of the seal). The root cause of the problem was confirmed when, without changing the seal profile, rod seal leakage was eliminated by discontinuing the practice of unloading the hydraulic ram. Warning! In certain situations, leaving loads suspended on hydraulic equipment can pose a safety hazard. For this reason, it is recommended that a safety risk assessment be carried out on a case-by-case basis before adopting this practice.

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-ram.html (2 of 3) [5/10/2004 7:58:52 PM]

Hydraulic Ram, Hydraulic Lift

http://www.insidersecretstohydraulics.com/hydraulic-ram.html (3 of 3) [5/10/2004 7:58:52 PM]

Hydraulic Symbol, Hydraulic Symbols

The value of the humble hydraulic symbol I am regularly involved in troubleshooting problems with hydraulic equipment. In these situations, there are two things I always do before reaching for my test gear. The first is to conduct a visual inspection of the hydraulic system, checking all the obvious things that could cause the problem in question (never overlook the obvious). The second is to ask for the schematic diagram for the hydraulic circuit.

What is a hydraulic schematic diagram? A hydraulic schematic diagram is a line drawing composed of hydraulic symbols that indicate the types of components the hydraulic circuit contains and how they are interconnected.

What makes a hydraulic schematic diagram valuable? A schematic diagram is a 'road map' of the hydraulic system and to a technician skilled in reading and interpreting hydraulic symbols, is a valuable aid in identifying possible causes of a problem. This can save a lot of time and money when troubleshooting hydraulic problems. If a schematic diagram is not available, the technician must trace the hydraulic circuit and identify its components in order to isolate possible causes of the problem. This can be a time-consuming process, depending on the complexity of the system. Worse still, if the circuit contains a valve manifold, the manifold may have to be removed and dismantled - just to establish what it's supposed to do. Reason being, if the function of a component within a hydraulic system is not known, it can be difficult to discount it as a possible cause of the problem. The humble hydraulic symbol eliminates the need to 'reverse engineer' the hydraulic circuit.

Where are all the hydraulic schematic diagrams? As most hydraulic technicians know, there's usually a better than even chance that a schematic diagram will not be available for the machine they've been called in to troubleshoot. This is unlikely to bother the technician because it is the machine owner who pays for its absence.

http://www.insidersecretstohydraulics.com/hydraulic-symbol.html (1 of 2) [5/10/2004 7:58:53 PM]

Hydraulic Symbol, Hydraulic Symbols

Where do all the hydraulic schematic diagrams go? They get lost or misplaced, they don't get transferred to the new owner when a machine is bought secondhand and in some cases they may not be issued to the machine owner at all. Why? Because generally speaking, hydraulic equipment owners don't place a lot of value on them. So if you're responsible for hydraulic equipment and you don't have schematic diagrams for your existing machines, try to obtain them - before you need them. And ensure that you are issued with schematic diagrams for any additional hydraulic machines you acquire. It will save you money in the long run.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-symbol.html (2 of 2) [5/10/2004 7:58:53 PM]

Hydraulic fluid decompression

Compression and decompression of hydraulic fluid One of our readers wrote to me recently regarding the following problem: "I have a problem with a large garbage compactor. Each and every time the valve cycles the hydraulic cylinder, there is a loud bang. What are the possible causes?" Assuming this noise is being generated by the hydraulics, i.e. it is not a symptom of a mechanical problem, its likely cause is uncontrolled decompression of the hydraulic fluid.

Hydraulic fluid bulk modulus and decompression This problem arises because hydraulic fluid is not perfectly rigid. The ratio of a fluid's decrease in volume as a result of increase in pressure is given by its bulk modulus of elasticity. The bulk modulus for hydrocarbon-based hydraulic fluids is approximately 250,000 PSI, (17,240 bar) which results in a volume change of around 0.4% per 1,000 PSI (70 bar). The formula for calculating the volume change of a hydraulic fluid under pressure using its bulk modulus is available here. When the change in volume exceeds 10 cubic inches (160 cubic centimeters) decompression must be controlled. The compression of hydraulic fluid results in storage of energy, similar to the potential energy stored in a compressed spring. Like a compressed spring, compressed fluid has the ability to do work. If decompression is not controlled, the stored energy dissipates instantaneously. This sudden release of energy accelerates the fluid, which does work on anything in its path. Uncontrolled decompression stresses hydraulic hose, pipe and fittings, creates noise and can cause pressure transients that damage hydraulic components.

Troubleshooting decompression problems Decompression is an inherent problem in hydraulic press applications, which have large volume cylinders operating at high pressures (a garbage compactor is effectively a press). Although hydrocarbon-based hydraulic fluids compress 0.4% - 0.5% by volume per 1,000 PSI, in actual application it is wise to calculate compression at 1% per 1,000 PSI. This compensates for the elasticity of the cylinder and conductors and http://www.insidersecretstohydraulics.com/hydraulic-decompression.html (1 of 3) [5/10/2004 7:59:00 PM]

Hydraulic fluid decompression

a possible increase in the volume of air entrained in the fluid. So if the combined captive volume of the hydraulic cylinder and conductors on our garbage compactor was 10 gallons and operating pressure was 5,000 PSI, the volume of compressed fluid would be 0.5 gallons (10 x 0.01 x 5). This equates to potential energy of around 33,000 watt-seconds. If the release of this amount of energy is not controlled, you can expect to hear a bang!

Controlling decompression Decompression is controlled by converting the potential energy of the compressed fluid into heat. This is achieved by metering the compressed volume of fluid across an orifice. A simple decompression control circuit, which will eliminate the bang from our garbage compactor, is shown below.

http://www.insidersecretstohydraulics.com/hydraulic-decompression.html (2 of 3) [5/10/2004 7:59:00 PM]

Hydraulic fluid decompression

When the directional control valve (1) is activated to extend the hydraulic cylinder (5), fluid enters the cylinder via the check valve (2). Pressurization of the cylinder during extension closes the pressure reducing valve (3), so that when the directional control valve (1) is activated to retract the cylinder (5) the compressed volume of fluid is metered across the orifice (4). When pressure upstream of the orifice (4) falls below the setting of the pressure reducing valve (3) the remaining fluid in the cylinder flows back to tank across the pressure reducing valve (3). The sequence valve (6) prevents pressurization of the rod side of the cylinder before the piston side has decompressed and the pressure reducing valve (3) has opened.

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-decompression.html (3 of 3) [5/10/2004 7:59:00 PM]

Hydraulic Cylinder, Hydraulic Cylinder Rods

Hydraulic cylinder rods turn black Black nitride is a relatively recent alternative to the hard-chrome plated hydraulic cylinder rod. With reports of achieved service life three times that of conventional chrome, longer seal life and comparable cost, black nitride rods for hydraulic cylinders are an option that all hydraulic equipment users should be aware of. Black nitriding is an atmospheric furnace treatment developed and patented in the early 1980's. It combines the high surface hardness and corrosion resistance of nitriding with additional corrosion resistance gained by oxidation. The process begins with the cleaning and super-polishing of the material to a surface roughness of 6 to 10 Ra. The steel bars or tubes are then fixed vertically, and lowered into an electrically heated pit furnace. The furnace sequence involves nitrocarburizing the steel at temperatures up to 1150ºF in an ammonia atmosphere. The steel's surface is converted to iron nitride to a depth of typically 0.001". Atmospheric oxidizing is employed to produce a black, corrosion resistant surface film. The process generates a thin (0.001") uniform and extremely hard (64 to 71 Rc) iron nitride layer infused with a film of iron oxide. Beneath the iron nitride layer is a nitrogenenriched, hardened diffusion zone. The diffusion zone functions as a lightly hardened case with a hardness gradient ranging from around 55 Rc just below the iron nitride layer to approximately 40 Rc at a depth of 0.015". Testing has verified that black nitride bar machines and welds as well as hard chrome plated stock. Available in standard diameters up to 5" (127 mm), black nitride hydraulic cylinder rods offer the following benefits over conventional hard chrome: ● ● ● ● ● ●

Superior corrosion and wear resistance Better oil retention (longer seal life) Dimensional uniformity Dent resistant - without the need for induction hardening No pitting, flaking or micro-cracking Environmentally friendly process

http://www.insidersecretstohydraulics.com/hydraulic-cylinder-rods.html (1 of 2) [5/10/2004 7:59:01 PM]

Hydraulic Cylinder, Hydraulic Cylinder Rods

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-cylinder-rods.html (2 of 2) [5/10/2004 7:59:01 PM]

Variable hydraulic pump efficiency

Determining hydraulic pump condition using volumetric efficiency I was recently asked to give a second opinion on the condition of a variable displacement hydraulic pump. My client had been advised that its volumetric efficiency was down to 80%. Based on this advice, he was considering having this hydraulic pump overhauled.

What is volumetric efficiency? Volumetric efficiency is the percentage of theoretical pump flow available to do useful work. In other words, it is a measure of a hydraulic pump's volumetric losses through internal leakage. It is calculated by dividing the pump's actual output in liters or gallons per minute by its theoretical output, expressed as a percentage. Actual output is determined using a flow-tester to load the pump and measure its flow rate. Because internal leakage increases as operating pressure increases and fluid viscosity decreases, these variables should be stated when stating volumetric efficiency. For example, a hydraulic pump with a theoretical output of 100 GPM, and an actual output of 94 GPM at 5000 PSI and 120 SUS is said to have a volumetric efficiency of 94% at 5000 PSI and 120 SUS. In practice, fluid viscosity is established by noting the fluid temperature at which actual output is measured and reading the viscosity off the temperature/viscosity graph for the grade of fluid in the hydraulic system.

What is the significance of volumetric efficiency? As a hydraulic pump wears in service, internal leakage increases and therefore the percentage of theoretical flow available to do useful work (volumetric efficiency) decreases. If volumetric efficiency falls below a level considered acceptable for the application, the pump will need to be overhauled.

Calculating the volumetric efficiency of variable hydraulic pumps The hydraulic pump in question had a theoretical output of 1,000 liters per minute at full displacement and maximum rpm. Its actual output was 920 liters per minute at 4,350 PSI and 100 SUS. When I advised my client that the pump's volumetric http://www.insidersecretstohydraulics.com/variable-hydraulic-pump.html (1 of 2) [5/10/2004 7:59:03 PM]

Variable hydraulic pump efficiency

efficiency was in fact 92%, he was alarmed by the conflicting results. To try and explain the disparity, I asked to see the first technician's test report. After reviewing this test report, I realized that the results actually concurred with mine, but had been interpreted incorrectly. The test had been conducted to the same operating pressure and at a fluid temperature within one degree of my own test, but at reduced displacement. The technician had limited the pump's displacement to give an output of 400 liters per minute at maximum rpm and no load (presumably the maximum capacity of his flow-tester). At 4,350 PSI the recorded output was 320 liters per minute. From these results, volumetric efficiency had been calculated to be 80% (320/400 x 100 = 80). To help understand why this interpretation is incorrect, think of the various leakage paths within a hydraulic pump as fixed orifices. The rate of flow through an orifice is dependant on the diameter (and shape) of the orifice, the pressure drop across it and fluid viscosity. This means that if these variables remain constant, the rate of internal leakage remains constant, independent of the pump's displacement. Note that in the above example, the internal leakage in both tests was 80 liters per minute. If the same test were conducted with pump displacement set to 100 liters per minute at no load, pump output would be at 20 liters per minute at 4,350 PSI - all other things being equal. This means that this pump has a volumetric efficiency of 20% at 10% displacement, 80% at 40% displacement and 92% at 100% displacement. As you can see, if actual pump output is measured at less than full displacement (or maximum rpm) an adjustment needs to be made when calculating volumetric efficiency.

Time for an overhaul? In considering whether it is necessary to have this hydraulic pump overhauled, the important number is volumetric efficiency at 100% displacement, which is within acceptable limits. If my client had based their decision on volumetric efficiency at 40% displacement, they would have paid thousands of dollars for unnecessary repairs.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/variable-hydraulic-pump.html (2 of 2) [5/10/2004 7:59:03 PM]

Hydraulic System Overheating Problems

Solving hydraulic system overheating problems I was asked recently to investigate and solve an overheating problem in a mobile hydraulics application. The hydraulic system comprised a diesel-hydraulic power unit, which was being used to power a pipe-cutting saw. The saw was designed for sub-sea use and was connected to the hydraulic power unit on the surface via a 710-foot umbilical. The operating requirements for the saw were 24 gpm at 3000 psi.

Why do hydraulic systems overheat? Heating of hydraulic fluid in operation is caused by inefficiencies. Inefficiencies result in losses of input power, which are converted to heat. A hydraulic system's heat load is equal to the total power lost (PL) through inefficiencies and can be expressed as: PLtotal = PLpump + PLvalves + PLplumbing + PLactuators If the total input power lost to heat is greater than the heat dissipated, the hydraulic system will eventually overheat.

Hydraulic fluid temperature - how hot is 'too hot'? Hydraulic fluid temperatures above 180°F (82°C) damage most seal compounds and accelerate degradation of the oil. While the operation of any hydraulic system at temperatures above 180°F should be avoided, fluid temperature is too high when viscosity falls below the optimum value for the hydraulic system's components. This can occur well below 180°F, depending on the fluid's viscosity grade.

Maintaining stable hydraulic fluid temperature To achieve stable fluid temperature, a hydraulic system's capacity to dissipate heat must exceed its inherent heat load. For example, a system with continuous input power of 100 kW and an efficiency of 80% needs to be capable of dissipating a heat load of at least 20 kW. It's important to note that an increase in heat load or a reduction in a hydraulic system's capacity to dissipate heat will alter the balance between heat load and dissipation. Returning to the above example, the hydraulic power unit had a continuous power http://www.insidersecretstohydraulics.com/hydraulic-system-overheating.html (1 of 3) [5/10/2004 7:59:04 PM]

Hydraulic System Overheating Problems

rating of 37 kW and was fitted with an air-blast heat exchanger. The exchanger was capable of dissipating 10 kW of heat under ambient conditions or 27% of available input power (10/37 x 100 = 27). This is adequate from a design perspective. The performance of all cooling circuit components were operating within design limits.

Pressure drop means heat At this point it was clear that the overheating problem was being caused by excessive heat load. Concerned about the length of the umbilical, I calculated its pressure drop. The theoretical pressure drop across 710 feet of ¾" pressure hose at 24 gpm is 800 psi. The pressure drop across the same length of 1" return hose is 200 psi. The formula for these calculations is available here. The theoretical heat load produced by the pressure drop across the umbilical of 1,000 psi (800 + 200 = 1000) was 10.35 kW. The formula for this calculation is available here. This meant that the heat load of the umbilical was 0.35 kW more than the heat dissipation capacity of the hydraulic system's heat exchanger. This, when combined with the system's normal heat load (inefficiencies) was causing the hydraulic system to overheat.

Beat the heat There are two ways to solve overheating problems in hydraulic systems: ● ●

decrease heat load; or increase heat dissipation.

Decreasing heat load is always the preferred option because it increases the efficiency of the hydraulic system. In the above example, the heat load of the umbilical alone was nearly 30% of available input power, a figure that would normally be considered unacceptable. Decreasing this heat load to an acceptable level would have involved reducing the pressure drop, by replacing the pressure and return lines in the umbilical with larger diameter hoses. The cost of doing this for what was a temporary installation meant that, in this case, the most economical solution was to install additional cooling capacity in the circuit Continuing to operate a hydraulic system when the fluid is over-temperature is similar to operating an internal combustion engine with high coolant temperature. Damage is guaranteed. Therefore, whenever a hydraulic system starts to overheat, shut it down, identify the cause and fix it.

http://www.insidersecretstohydraulics.com/hydraulic-system-overheating.html (2 of 3) [5/10/2004 7:59:04 PM]

Hydraulic System Overheating Problems

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-system-overheating.html (3 of 3) [5/10/2004 7:59:04 PM]

Hydraulic Cylinders, Hydraulic Cylinder

Hydraulic cylinders - checking rod straightness As a product group, hydraulic cylinders are almost as common as pumps and motors combined. They are less complicated than other types of hydraulic components and are therefore relatively easy to repair. As a result, many hydraulic equipment owners or their maintenance personnel repair hydraulic cylinders in-house. An important step in the repair process that is often skipped by do-it-yourself repairers, is the checking of rod straightness.

How do bent rods affect hydraulic cylinders? Bent rods load the rod seals causing distortion, and ultimately premature failure of the hydraulic cylinders seals.

Allowable run-out Rod straightness should always be checked when hydraulic cylinders are being resealed or repaired. This is done by placing the rod on rollers and measuring the runout with a dial gauge. The rod should be as straight as possible, but a run-out of 0.5 millimeters per linear meter of rod is generally considered acceptable.

Straightening hydraulic cylinder rods In most cases, bent rods can be straightened in a press. It is sometimes possible to straighten hydraulic cylinder rods without damaging the hard-chrome plating, however if the chrome is damaged, the rod must be either re-chromed or replaced.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-cylinders.html (1 of 2) [5/10/2004 7:59:06 PM]

Hydraulic Cylinders, Hydraulic Cylinder

http://www.insidersecretstohydraulics.com/hydraulic-cylinders.html (2 of 2) [5/10/2004 7:59:06 PM]

Hydraulic Pump, Hydraulic Pumps

Hydraulic pump life cut short by particle contamination I was recently asked to conduct failure analysis on a hydraulic pump that had an expected service life of 10,000 hours. The pump had been removed from its machine after achieving only 2000 hours in service. Analysis revealed that this hydraulic pump hadn't actually failed - it had been 'wornout' through abrasion caused by contaminated hydraulic fluid.

What is 'contaminated hydraulic fluid'? Contaminants of hydraulic fluid include solid particles, air, water or any other matter that impairs the function of the fluid.

How does contamination affect a hydraulic pump? Particle contamination accelerates wear of hydraulic components. The rate at which damage occurs is dependent on the internal clearance of the components within the system, the size and quantity of particles present in the fluid, and system pressure. Particles larger than the component's internal clearances are not necessarily dangerous. Particles the same size as the internal clearances cause damage through friction. However, the most dangerous particles in the long term are those that are smaller than the component's internal clearances. Particles smaller than 5 microns are highly abrasive. If present in sufficient quantities, these invisible 'silt' particles cause rapid wear, destroying hydraulic pumps and other components.

How can this type of hydraulic pump failure be prevented? While the type of failure described above is unusual in properly designed hydraulic systems that are correctly maintained, this example highlights the importance of monitoring hydraulic fluid cleanliness levels at regular intervals.

http://www.insidersecretstohydraulics.com/hydraulic-pump.html (1 of 2) [5/10/2004 7:59:07 PM]

Hydraulic Pump, Hydraulic Pumps

As in this case, if the high levels of silt particles present in the hydraulic fluid had been identified and the problem rectified early enough, the damage to this hydraulic pump and the significant expense of its repair could have been avoided.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-pump.html (2 of 2) [5/10/2004 7:59:07 PM]

Hydraulic Press, Hydraulic Presses

Hydraulic press failure illustrates the importance of scheduling change-outs A manufacturing company recently hired me to check the performance of four piston pumps operating a large hydraulic press. The pumps had clocked over 10,000 hours in service and the customer's concern was that if pump performance was down, production would be too. My test results revealed that the performance of all four pumps was within acceptable limits. In my report, I advised my client that there would only be a minimal increase in productivity if the pumps were replaced. I further advised that the change-out of all four pumps should be scheduled urgently. The foundation for this recommendation was that the pumps had exceeded their expected service life and in the absence of an effective condition-based maintenance program, the probability of an in-service bearing failure was significantly increased. When a hydraulic component fails in service, large amounts of metallic particles are generated. These particles circulate in the hydraulic fluid, often causing damage to other components before the system's filters can remove them. In extreme cases, the contamination load can clog the filters, which results in unfiltered fluid being circulated through the system. A component that fails in service is almost always more expensive to rebuild than a component that is removed from service in a pre-failed condition. A failure in service usually results in mechanical damage to the internal parts of the component. As a consequence, parts that would have been serviceable have to be replaced. In extreme cases, components that would have been economical to repair become uneconomical to repair, increasing the cost of component replacement by up to 40%. The client took my advice, but unfortunately, a bearing failed in one of the pumps before all of the change-outs were completed. A piece of cage from the failed bearing found its way into the main hydraulic press cylinder, causing $6,000 damage. The pump that failed cost 50% more to rebuild than the three units that were removed from service in pre-failed condition. Not to mention the downtime cost of the hydraulic press. The additional repair costs in this case were significant and could have been avoided, http://www.insidersecretstohydraulics.com/hydraulic-press.html (1 of 2) [5/10/2004 7:59:08 PM]

Hydraulic Press, Hydraulic Presses

if the pumps had been changed-out once they achieved their expected service life. To minimize the chances of hydraulic components failing in service, the machine manufacturers' recommendations on expected service life should be used to schedule component change-outs. It may be possible to safely extend service life beyond that recommended through careful application of condition-based monitoring techniques, such as oil analysis (wear debris analysis). But unless an effective, predictive maintenance program is in place, running hydraulic components beyond their expected service life is false economy.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-press.html (2 of 2) [5/10/2004 7:59:08 PM]

Hydraulic Motor,Hydraulic Motors

Hydraulic motors - how dry starts damage them I was asked recently to conduct failure analysis on a hydraulic motor that was the subject of a warranty claim. The motor had failed after only 500 hours in service, some 7,000 hours short of its expected service life. Inspection revealed that the motor's bearings had failed through inadequate lubrication, as a result of the motor being started with insufficient fluid in its case (housing). A common misconception among maintenance personnel with limited training in hydraulics, is that because oil circulates through hydraulic components in operation, no special attention is required during installation, beyond fitting the component and connecting its hoses. Nothing could be further from the truth. After this hydraulic motor was installed, its case should have been filled with clean oil prior to start-up. Starting a piston-type motor or pump without doing so, is similar to starting an internal combustion engine with no oil in the crankcase - premature failure is pretty much guaranteed. Some of you may be thinking that the case should fill with fluid through internal leakage. In most cases it will, but not before the motor or pump has been damaged. In many cases, this damage may not show itself until the component fails prematurely, hundreds or even thousands of service hours after the event. In this particular example the warranty claim was rejected on the basis of improper commissioning and the customer was lumbered with an expensive repair bill.

How can this type of failure be prevented? This example highlights the importance of following proper commissioning procedures when installing hydraulic components. As in this example, if the case of the hydraulic motor had been filled with fluid prior to start-up, the failure of this motor and the significant expense of its repair could have been prevented.

http://www.insidersecretstohydraulics.com/hydraulic-motor.html (1 of 2) [5/10/2004 8:04:30 PM]

Hydraulic Motor,Hydraulic Motors

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-motor.html (2 of 2) [5/10/2004 8:04:30 PM]

Hydraulic Valve,Hydraulic Valves

Hydraulic valves - preventing cavitation damage A client recently asked me to advise them on the possibility of repairing a large hydraulic valve off a 400 ton excavator, used in open-cut mining. The valve in question was a spool-type directional control. It had been badly damaged as a result of cavitation, which had occurred over a long period in service.

What is cavitation? Cavitation occurs when the volume of fluid demanded by any part of a hydraulic circuit exceeds the volume of fluid being supplied. This causes the absolute pressure in that part of the circuit to fall below the vapor pressure of the hydraulic fluid. This results in the formation of vapor bubbles within the fluid, which implode when compressed. Cavitation causes metal erosion, which damages hydraulic components and contaminates the hydraulic fluid. In extreme cases, cavitation can result in major mechanical failure of pumps and motors. While cavitation commonly occurs at the pump, it can occur just about anywhere within a hydraulic circuit. In the hydraulic valve described above, the metal erosion in the body of the valve was so severe that the valve was no longer serviceable. The valve had literally been eaten away from the inside, as a result of chronic cavitation. In this particular case the cause of the cavitation was faulty anti-cavitation valves, which are designed to prevent this type of damage from occuring.

How can this type of failure be prevented? This example highlights the importance of checking the operation and adjustment of circuit protection devices, including anti-cavitation and load control valves, at regular intervals.

http://www.insidersecretstohydraulics.com/hydraulic-valve.html (1 of 2) [5/10/2004 8:04:31 PM]

Hydraulic Valve,Hydraulic Valves

As in this case, if the faulty anti-cavitation valves had been identified and replaced early enough, the damage to this hydraulic valve and the significant expense of its replacement could have been avoided.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-valve.html (2 of 2) [5/10/2004 8:04:31 PM]

Hydraulic Hose, Hydraulic Hoses

Hydraulic hose failure costs and prevention Hydraulic hose has a finite service life, which can be reduced by a number of factors. From a maintenance perspective, little or no attention is usually paid to the hoses of a hydraulic system until a failure occurs. Hydraulic hose failures cost more than the replacement hose. Additional costs can include: ● ●

● ●

Clean up, disposal and replacement of lost hydraulic fluid. Collateral damage to other components, e.g. a hose failure on a hydrostatic transmission can result in loss of charge pressure and cavitation damage to the transmission pump and/or motor. Possible damage caused by the ingression of contaminants. Machine downtime.

What causes hydraulic hose failures? Focus on the following points to extend hydraulic hose life and minimize the costs associated with hydraulic hose failures:

External damage Hydraulic hose manufacturers estimate that 80% of hose failures are attributable to external physical damage through pulling, kinking, crushing or abrasion of the hose. Abrasion caused by hoses rubbing against each other or surrounding surfaces is the most common type of damage. To prevent external damage, ensure all clamps are kept secure, pay careful attention to routing whenever a replacement hose is installed and if necessary, apply inexpensive polyethylene spiral wrap to protect hydraulic hoses from abrasion.

Multi-plane bending Bending a hydraulic hose in more than one plane results in twisting of its wire reinforcement. A twist of five degrees can reduce the service life of a high-pressure hydraulic hose by as much as 70% and a seven degree twist can result in a 90% http://www.insidersecretstohydraulics.com/hydraulic-hose.html (1 of 2) [5/10/2004 8:04:33 PM]

Hydraulic Hose, Hydraulic Hoses

reduction in service life. Multi-plane bending is usually the result of poor hose-assembly selection and/or routing but can also occur as a result of inadequate or unsecure clamping where the hose is subjected to machine or actuator movement.

Operating conditions The operating conditions that a correctly installed hydraulic hose is subjected to will ultimately determine its service life. Extremes in temperature, e.g. high daytime operating temperatures and very cold conditions when the machine is standing at night, accelerate aging of the hose's rubber tube and cover. Frequent and extreme pressure fluctuations, e.g. rock hammer on a hydraulic excavator, accelerate hose fatigue. In applications where a two-wire braid reinforced hydraulic hose meets the nominal working pressure requirement but high dynamic pressure conditions are expected, the longer service life afforded by a spiral reinforced hydraulic hose will usually more than offset the higher initial cost.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-hose.html (2 of 2) [5/10/2004 8:04:33 PM]

Hydraulic System, Hydraulic Systems

Hydraulic system troubleshooting - check the easy things first In Part II of Insider Secrets to Hydraulics, I outline a logical approach to hydraulic system troubleshooting that begins with checking and eliminating the easy things first. The benefits of this approach are clearly illustrated by a troubleshooting situation I was involved in recently. The machine in question had a complex hydraulic system, the heart of which comprised two engines driving ten pumps. Six of the pumps were variable displacement units and four of these had electronic horsepower control. The symptoms of the problem were slow cycle times in combination with lug-down of the engines (loss of engine rpm). The machine had just been fitted with a new set of pumps. The diagnosis of the mechanic in charge was that the hydraulic system was tuned above the power curve of the engines i.e. the hydraulics were demanding more power than the engines could produce, resulting in lug-down of the engines and therefore slow cycle times. The other possible explanation of course, was that the engines were not producing their rated horsepower. Due to the complexity of the hydraulic system, I knew that it would take around four hours to run a complete system check and tune-up. So in order to eliminate the easy things first, when I arrived on site I inquired about the condition of the engines and their service history. The mechanic in charge not only assured me that the engines were in top shape, he was adamant that this was a "hydraulic" problem. Four hours later, after running a complete check of the hydraulic system without finding anything significant, I was not surprised that the problem remained unchanged. After a lengthy discussion, I managed to convince the mechanic in charge to change the fuel filters and air cleaner elements on both engines. This fixed the problem. It turned out that a bad batch of fuel had caused premature clogging of the engine fuel filters, which were preventing the engines from developing their rated horsepower.

http://www.insidersecretstohydraulics.com/hydraulic-system.html (1 of 2) [5/10/2004 8:04:34 PM]

Hydraulic System, Hydraulic Systems

If the relatively simple task of changing the engine fuel filters had been carried out when the problem was first noticed, an expensive service call and four hours of downtime could have been avoided.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-system.html (2 of 2) [5/10/2004 8:04:34 PM]

Hydraulic Cylinder Maintenance

Proactive maintenance for hydraulic cylinders Damaged hydraulic cylinder rods and wiper seals are an eternal problem for users of hydraulic machinery. Dents and gouges on the surface of hydraulic cylinder rods reduce seal life and give dust and other contaminants an easy path into the hydraulic system. These silt-sized particles act like lapping compound, initiating a chain of wear in hydraulic components. In response to this problem, a protective cylinder rod cover called Seal Saver has been developed and patented. Seal Saver is not a typical bellows boot you may already be familiar with. It is a continuous piece of durable material, which wraps around the cylinder and is closed with Velcro. It is then clamped onto the cylinder body and rod end. This makes installation simple with no disassembly of hydraulic cylinder components required.

Seal Saver forms a protective shroud over the cylinder rod as it strokes and prevents buildup of contaminants around the wiper seal - a common cause of rod scoring, seal damage and contaminant ingress. Research has shown that the cost to remove contaminants is ten times the cost of exclusion. This, combined with the benefits of extended hydraulic cylinder rod and seal life, makes Seal Saver a cost-effective, proactive maintenance solution.

http://www.insidersecretstohydraulics.com/hydraulic-cylinder-maintenance.html (1 of 2) [5/10/2004 8:04:39 PM]

Hydraulic Cylinder Maintenance

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-cylinder-maintenance.html (2 of 2) [5/10/2004 8:04:39 PM]

Hydraulic Fitting

Hydraulic fitting selection the key to leak-free hydraulic plumbing Hydraulic fitting leaks are often considered to be an inherent characteristic of hydraulic machines. While this may have been true 30 years ago, advances in sealing technology and the development of reliable connection systems means that today, leak-free hydraulic plumbing is readily achievable.

Reliable Connections Leak-free reliability begins at the design stage, when the type of hydraulic fitting is selected for port, tube-end and hose-end connections. Ports - Connectors that incorporate an elastomeric seal such as UNO, BSPP and SAE 4-bolt flange offer the highest seal reliability. NPT is the least reliable type of connector for high-pressure hydraulic systems because the thread itself provides a leak path. The threads are deformed when tightened and as a result, any subsequent loosening or tightening increases the potential for leaks. In existing systems, pipe thread connections should be replaced with UNO or BSPP for leak-free reliability. Tube and Hose Ends - ORFS tube and hose end connections feature the high seal reliability afforded by an elastomeric seal but, due to its cost, ORFS is not as widely used as compression fittings and JIC 37-degree flare. Flared connections have gained widespread acceptance due to their simplicity and low cost. However, the metal-to-metal seal of the flare means that a permanent, leak-free joint is not always achieved, particularly in the case of tube-end connections. Leaking flare joints can be eliminated using a purpose-built seal developed by Flaretite. The Flaretite seal is a stainless steel stamping shaped like a JIC nose, with concentric ribs that contain pre-applied sealant. When tightened, the ribs crush between the two faces of the joint, eliminating any misalignment and surface imperfections. The combination of the crush on the ribs and the sealant ensure that a leak-free joint is achieved.

Incorrect Torque

http://www.insidersecretstohydraulics.com/hydraulic-fitting.html (1 of 3) [5/10/2004 8:04:41 PM]

Hydraulic Fitting

A common cause of leaks from flare joints is incorrect torque. Insufficient torque results in inadequate seat contact, while excessive torque can result in damage to the tube and fitting through cold working. The following is a simple method to ensure flare joints are correctly torqued:

1. Finger tighten the nut until it bottoms on the seat. 2. Using a permanent marker, draw a line lengthwise across the nut and fitting. 3. Wrench tighten the nut until it has been rotated the number of hex flats listed in the following table:

Tube Dash Size Hex Flats 4

2.5

5

2.5

6

2.0

8

2.0

10

1.5 - 2.0

12

1.0

16

0.75 - 1.0

20

0.75 - 1.0

24

0.5 - 0.75

Vibration Vibration can stress plumbing, affecting hydraulic fitting torque and causing fatigue. Tube is more susceptible than hose. If vibration is excessive, the root cause should be addressed. Ensure all conductors are adequately supported and if necessary, replace problematic tubes with hose.

Seal Damage Having outlined the benefits of hydraulic fittings that incorporate an elastomeric seal, it is important to note that their reliability is contingent on fluid temperature being maintained within acceptable limits. A single over-temperature event of sufficient magnitude can damage all the seals in a hydraulic system, resulting in numerous leaks.

Conclusion A leak-free hydraulic system should be considered the norm for modern hydraulic machines - not the exception. But the proper selection, installation and maintenance of hydraulic plumbing are essential to ensure leak-free reliability.

http://www.insidersecretstohydraulics.com/hydraulic-fitting.html (2 of 3) [5/10/2004 8:04:41 PM]

Hydraulic Fitting

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-fitting.html (3 of 3) [5/10/2004 8:04:41 PM]

Hydraulic Seal, Hydraulic Seals

The top four causes of hydraulic seal failure in cylinders Hydraulic cylinder seals cost the manufacturer pennies. They are usually purchased on a low bid basis. But that simple, inexpensive hydraulic seal can cost you thousands in downtime and loss of production if it fails. If you have a problem seal, focus on these four points to help determine the cause of failure. No. 1 - Improper installation is a major cause of hydraulic seal failure. The important things to watch during seal installation are: (a) cleanliness, (b) protecting the seal from nicks and cuts, and (c) proper lubrication. Other problem areas are over tightening of the seal gland where there is an adjustable gland follower or folding over a seal lip during installation. Installing the seal upside down is a common occurrence, too. The solution to these problems is common sense and taking reasonable care during assembly. No. 2 - Hydraulic system contamination is a another major factor in hydraulic seal failure. It is usually caused by external elements such as dirt, grit, mud, dust, ice and internal contamination from circulating metal chips, break-down products of fluid, hoses or other degradable system components. As most external contamination enters the system during rod retraction, the proper installation of a rod wiper/scraper is the best solution. Internal contamination can be prevented by proper filtering of system fluid. Contamination is indicated by scored rod and cylinder bore surfaces, excessive seal wear and leakage - and sometimes tiny pieces of metal imbedded in the seal. No. 3 - Chemical breakdown of the seal material is most often the result of incorrect material selection in the first place, or a change of hydraulic system fluid. Misapplication or use of non-compatible materials can lead to chemical attack by fluid additives, hydrolysis and oxidation reduction of seal elements. Chemical breakdown can result in loss of seal lip interface, softening of seal durometer, excessive swelling or shrinkage. Discoloration of hydraulic seals can also be an indicator of chemical attack. No. 4 - Heat degradation is to be suspected when the failed seal exhibits a hard, brittle appearance and/or shows a breaking away of parts of the seal lip or body. Heat degradation results in loss of sealing lip effectiveness through excessive compression set and/or loss of seal material. Causes of this condition may be use of incorrect seal material, high dynamic friction, excessive lip loading, no heel clearance and proximity

http://www.insidersecretstohydraulics.com/hydraulic-seal.html (1 of 2) [5/10/2004 8:04:42 PM]

Hydraulic Seal, Hydraulic Seals

to outside heat source. Correction of heat degradation problems may involve reducing seal lip interference, increasing lubrication or a change of the seal material. In borderline situations consider all upper temperature limits to be increased by 50 degrees F in hydraulic cylinder seals at the seal interface due to running friction caused by the sliding action of the lips. Here's a secret - it is not necessary to buy replacement seals from the hydraulic cylinder manufacturer. Many hydraulic seal suppliers have the same exact seals that are used in most hydraulic cylinders and can easily cross reference or match up a replacement. In many cases, if there is a recurring problem with a seal, your seal specialist can recommend a solution and increase the life of the seal. About the author: Jerry Whitlock is known as The Seal Man™. He has over 30 years experience in the seal industry. Jerry owns EPM, Inc. located in Atlanta, GA. His web site www.epm.com is the largest and most visited web site for hydraulic seals on the Internet.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-seal.html (2 of 2) [5/10/2004 8:04:42 PM]

Hydraulic Filter,Hydraulic Filters

Hydraulic filters that do more harm than good - Part 1 Given that particle contamination of hydraulic fluid reduces the service life of hydraulic components, it would seem logical that a system can never have too many hydraulic filters. Well... not exactly. Some hydraulic filters can actually do more harm than good and therefore their inclusion in a system is sometimes misguided. Pump inlet (suction) filters fall into this category. Inlet filters usually take the form of a 140 micron, mesh strainer which is screwed onto the pump intake penetration inside the reservoir. Inlet filters increase the chances of cavitation occurring in the intake line and subsequent damage to, and failure of the pump. Piston-type pumps are particularly susceptible. If the reservoir starts out clean and all fluid returning to the reservoir is filtered, inlet filters are not required since the fluid will not contain particles large enough to be captured by a coarse mesh strainer.

What does this mean? I generally recommend removing and discarding inlet filters where fitted. The one possible exception to this rule is charge pump intakes on hydrostatic transmissions. If in doubt consult the pump manufacturer. If you are involved in the design of hydraulic systems, think twice before fitting hydraulic filters to pump intake lines.

http://www.insidersecretstohydraulics.com/hydraulic-filter.html (1 of 2) [5/10/2004 8:04:43 PM]

Hydraulic Filter,Hydraulic Filters

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-filter.html (2 of 2) [5/10/2004 8:04:43 PM]

Hydraulic Filter,Hydraulic Filters

Hydraulic filters that do more harm than good - Part 2 In response to my previous article on hydraulic filters and the negative effects of suction strainers, one of our readers wrote the following: "The one thing a suction strainer does that's worthwhile is to keep out the trash that gets dropped into the tank during service. We lost pumps to things like bolts that we know were not in the tank when it got built. The process of adding hydraulic fluid to the tank often doubles as the trash-installation function. The screens that are often installed in the fill neck usually get a hole poked through them so that oil will go in faster..." A couple of years ago, I was involved in a case where the seals failed in the swivel on an excavator. This allowed the automatic greasing system to pump grease into the hydraulic reservoir. The grease clogged the suction strainers, which subsequently failed. The wire mesh from the suction strainers destroyed all four pumps and several other components. Had suction strainers not been fitted, it is likely that the grease would have eventually dissolved in the hydraulic fluid with minimal damage to any components. My point is, I don't use this example as an argument against fitting suction strainers because grease should not be in the reservoir. Likewise, I do not consider trash exclusion to be a valid argument for fitting suction strainers - because nuts, bolts or similar debris should not be in the reservoir. The sloppy operators that allow trash to drop into the reservoir are the same operators that never drain and clean the reservoir, and change the suction strainer. So the suction strainer clogs eventually and the pump fails through cavitation. Therefore, with or without the suction strainer, the pump is destined to fail prematurely. The correct solution is not to allow trash to get into the reservoir. And this is fundamental to my recommendation to remove and discard suction strainers, where http://www.insidersecretstohydraulics.com/hydraulic-filter-2.html (1 of 2) [5/10/2004 8:04:45 PM]

Hydraulic Filter,Hydraulic Filters

fitted. Excessive vacuum at the pump inlet caused by suction strainers is a bigger threat to pump life in the long run, than trash that shouldn't be in the reservoir in the first place.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-filter-2.html (2 of 2) [5/10/2004 8:04:45 PM]

Hydraulic Filter,Hydraulic Filters

Hydraulic filters that do more harm than good - Part 3 In a previous article on hydraulic filters, I pointed out that all fluid returning to the reservoir should be filtered. The one exception to this rule is the case drains of piston pumps and motors. Connecting case drain lines to return filters can cause excessive case pressure, which has a number of damaging effects. High case pressure results in excessive load on the lip of the shaft seal. This causes the seal lip to wear a groove in the shaft, which eventually results in a leaking shaft seal. The effect of high case pressure on in-line piston pumps is the same as excessive vacuum at the pump inlet. Both conditions put the piston ball and slipper-pad socket in tension during intake. In severe cases this can result in buckling of the piston retaining plate and/or separation of the bronze slipper from the piston, causing major failure. Under certain conditions, high case pressure can cause the pistons of radial piston motors to be lifted off the cam during the outlet cycle. When this happens the pistons are hammered back onto the cam during inlet, destroying the motor.

What does this mean? The case drain line of piston pumps and motors should be returned to the reservoir through a dedicated penetration below minimum fluid level. For the reasons described above, hydraulic filters are not recommended on case drain lines. However, if a filter is fitted it should be generously oversized to minimize back pressure in the pump or motor case. If in doubt, consult the pump or motor manufacturer.

http://www.insidersecretstohydraulics.com/hydraulic-filter-3.html (1 of 2) [5/10/2004 8:04:46 PM]

Hydraulic Filter,Hydraulic Filters

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-filter-3.html (2 of 2) [5/10/2004 8:04:46 PM]

Hydraulic Power Unit

Hydraulic power unit problem highlights the value of hydraulic pump testing A client recently engaged me to design and build a hydraulic power unit for a specific application. The unit comprised a diesel engine driving an axial piston pump fitted with load sensing, power limiting and pressure limiting control.

What is a hydraulic power unit? A hydraulic power unit comprises a prime mover (usually an electric motor or combustion engine), hydraulic pump, tank, filters and valves.

What is hydraulic pump load sensing control? Load sensing control is so called because the load-induced pressure downstream of the directional control valve is sensed and hydraulic pump flow adjusted to maintain a constant pressure drop (and therefore flow) across the valve. For example, let's say we have a hydraulic pump driving a winch thru a manual, directional valve. The operator summons the winch by moving the spool in the directional valve 20% of its stroke. The winch drum turns at five rpm. For clarity, imagine that the directional valve is now a fixed orifice. Flow across an orifice decreases as the pressure drop across it decreases. As load on the winch increases, the load-induced pressure downstream of the orifice (directional valve) increases. This decreases the pressure drop across the orifice, which means flow decreases and the winch slows down. The load sensing control senses the load-induced pressure downstream of the orifice and adjusts hydraulic pump flow so that pressure upstream of the orifice increases by a corresponding amount. This keeps the pressure drop across the orifice (directional valve) constant, which keeps flow constant and in this case, winch speed constant. Because the hydraulic pump only produces the flow demanded by the actuators, load sensing control is energy efficient (fewer losses to heat) and as demonstrated in the above example, provides more precise control.

What is hydraulic pump power limiting control? http://www.insidersecretstohydraulics.com/hydraulic-power-unit.html (1 of 3) [5/10/2004 8:04:48 PM]

Hydraulic Power Unit

A constant power or power limiting control operates by reducing the displacement, and therefore flow, from the hydraulic pump as pressure increases, so that the power rating of the prime mover is not exceeded. The advantage of this type of control is that more flow is available at lower pressures, so that the actuators can operate faster under light loads. This results in better utilization of the power available from the prime mover. The power limiting control overrides the load sensing control.

What is hydraulic pump pressure limiting control? Pressure limiting control limits the maximum operating pressure of the hydraulic pump. Also referred to as a pressure compensator or pressure cut-off. The pressure limiting control overrides both the load sensing and power limiting controls.

Hydraulic pump control problem A new hydraulic pump was ordered for the project from a leading manufacturer. When the hydraulic power unit was commissioned, the power limiting control was not functioning. When advised of the problem, the manufacturer maintained that the pump had been tested prior to delivery and that the cause of problem therefore must be elsewhere in the circuit. Possible external causes were quickly checked and eliminated. While waiting for the manufacturer to respond to the problem, I checked the schematic diagram of the pump's control and noticed that a vital part was missing.

Plug-in controls The power limiting control on this particular hydraulic pump is a modular, screw-in cartridge fitted to the standard pump with load sensing and pressure limiting control. The power limiting cartridge is a relief valve with a link to the swash plate that increases spring bias as swash angle decreases. This relief valve limits load signal pressure depending on swash plate position. When the allowable power setting is reached, the relief valve intervenes to reduce the load pressure signal to the load sensing control. This results in a decrease in swash angle and therefore flow. The lower the swash angle and therefore flow, the higher the load signal pressure and therefore operating pressure permissible. Because power is a product of flow and pressure, this limits the power draw of the hydraulic pump. If you examine the two hydraulic pump schematic diagrams closely, you will notice that other than the addition of a power limiting relief cartridge, there is a second difference. An orifice is shown just below the load sensing signal connection or X port. Without this orifice to limit the flow from the load sensing line, the power limiting relief valve cannot effectively limit the load pressure signal. This means that the power limiting control cannot function. I checked the pump fitted to the hydraulic power unit and it did not have this orifice http://www.insidersecretstohydraulics.com/hydraulic-power-unit.html (2 of 3) [5/10/2004 8:04:48 PM]

Hydraulic Power Unit

fitted. I advised the manufacturer and requested that they dispatch one of these orifices urgently. I was astonished by the manufacturer's reply - the required part was on back order. To minimize any further downtime, I manufactured an orifice, fitted it to the pump and handed the hydraulic power unit over to the customer.

Test for success Thoroughly testing new or rebuilt hydraulic components prior to dispatch ensures that the component will work the way it should and will perform within its design parameters. It is possible that the manufacturer tested the hydraulic pump discussed above - but only its load sensing and pressure limiting controls. Had the functionality of the power limiting control been tested, the pump would not have been dispatched without the necessary orifice. This would have avoided an embarrassing mistake for the manufacturer and many hours of downtime for the customer.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-power-unit.html (3 of 3) [5/10/2004 8:04:48 PM]

Hydraulic Oil, Hydraulic Oils

Adding hydraulic oil - without the dirt Hydraulic oil straight from the drum, has a typical cleanliness level of ISO 4406 21/18. A 25 GPM pump operating continuously in hydraulic oil at this cleanliness level will circulate 3,500 pounds of dirt to the hydraulic system's components each year! To add hydraulic oil, and not the dirt, always filter new oil prior to use in a hydraulic system. This can be accomplished by pumping the oil into the reservoir through the system's return filter. The easiest way to do this is to install a tee in the return line and attach a quick-connector to the branch of this tee. Attach the other half of the quick-connector to the discharge hose of a drum pump. When hydraulic oil needs to be added to the reservoir, the drum pump is coupled to the return line and the oil is pumped into the reservoir through the return filter. As well as filtering the oil, spills are avoided and the ingress of external contamination is prevented. The benefits of carrying out this simple modification are well worth the minor cost involved.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-oil.html [5/10/2004 8:04:49 PM]

Hydraulic Fluid,Hydraulic Fluids

Hydraulic fluid - getting the viscosity right Most hydraulic systems will operate satisfactorily using a variety of fluids, including multi-grade engine oil and automatic transmission fluid (ATF), in addition to the more conventional anti-wear (AW) hydraulic fluid - provided the viscosity is correct. Viscosity is the single most important factor when selecting a hydraulic fluid. It doesn't matter how good the anti-wear, anti-oxidization or anti-corrosion properties of the fluid are, if the viscosity grade is not correctly matched to the operating temperature range of the hydraulic system, maximum component life will not be achieved. Defining the correct fluid viscosity grade for a particular hydraulic system involves consideration of several interdependent variables. These are: ● ●

●

starting viscosity at minimum ambient temperature; maximum expected operating temperature, which is influenced by maximum ambient temperature; and permissible and optimum viscosity range for the system's components.

Once these parameters are known, the correct viscosity grade can be determined using the viscosity/temperature curve of a suitable type of fluid - commonly AW hydraulic fluid defined according to ISO viscosity grade (VG) numbers. Automatic transmission fluid, multi-grade engine oil and anti-wear, high VI (AWH) hydraulic fluid are commonly used in hydraulic systems that experience a wide operating temperature range. These fluids have a higher Viscosity Index (VI) than AW hydraulic fluids due to the addition of VI improvers. The higher the VI a fluid has, the smaller the variation in viscosity as temperature changes. In simple terms, this means that if you are running ATF(46) in your skid-steer loader, you can operate the hydraulics with a higher fluid temperature before viscosity falls below optimum, than you could if you were running ISO VG46 AW hydraulic fluid. When selecting a high VI fluid, the component manufacturer's minimum permissible viscosity value should be increased by 30% to compensate for possible loss of viscosity as a result of VI improver sheardown. VI improvers can have a negative effect on the demulsification and air separation http://www.insidersecretstohydraulics.com/hydraulic-fluid.html (1 of 2) [5/10/2004 8:04:50 PM]

Hydraulic Fluid,Hydraulic Fluids

properties of the fluid and for this reason some hydraulic component manufacturers recommend that these types of fluids only be used when operating conditions demand. As far as fluid recommendations go, for commercial reasons relating to warranty etc, I always advise following the machine manufacturer's recommendation. But in equipment that has a history of satisfactory performance and component life, there is usually no compelling reason to change the type of fluid being used.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-fluid.html (2 of 2) [5/10/2004 8:04:50 PM]

Hydraulic Fluid,Hydraulic Fluid Temperature

High hydraulic fluid temperature - how it causes premature failures I was asked recently to conduct failure analysis on two radial piston motors that had failed well short of their expected service life. Inspection revealed that the motors had failed through inadequate lubrication, as a result of low fluid viscosity caused by excessive hydraulic fluid temperature.

How does this happen? As the temperature of petroleum-based hydraulic fluid increases, its viscosity decreases. If fluid temperature increases to the point where viscosity falls below the level required to maintain a lubricating film between the internal parts of the component, damage will result. The temperature at which this occurs depends on the viscosity grade of the fluid in the system. Hydraulic fluid temperatures above 180°F (82°C) damage seals and reduce the service life of the fluid. But depending on the grade of fluid, viscosity can fall to critical levels well below this temperature.

How can this type of failure be prevented? The above example highlights the importance of not allowing fluid temperature to exceed the point at which viscosity falls below the optimum level for the system's components. Continuing to operate a hydraulic system when the fluid is over-temperature is similar to operating an internal-combustion engine with high coolant temperature. Damage is pretty much guaranteed. Therefore, whenever a hydraulic system starts to overheat, shut down the system, find the cause of the problem and fix it!

http://www.insidersecretstohydraulics.com/hydraulic-fluid-2.html (1 of 2) [5/10/2004 8:04:51 PM]

Hydraulic Fluid,Hydraulic Fluid Temperature

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-fluid-2.html (2 of 2) [5/10/2004 8:04:51 PM]

Hydraulic Fluid,Biodegradable Hydraulic Fluid

Biodegradable hydraulic fluid - its application and use A client recently engaged me to advise them on an application that required the use of biodegradable hydraulic fluid. This client was tendering on an earth-moving project located in environmentally sensitive wetlands. A condition of the contract was that the hydraulic systems of all equipment employed on the project use biodegradable fluid to minimize pollution in the case of leaks, especially hose failures. Biodegradable or biobased hydraulic fluids use vegetable oils such as canola, rapeseed, sunflower or soybean as the base oil. The properties of these fluids can be equivalent to that of mineral oil based, anti-wear hydraulic fluids. But due to limited application testing, some hydraulic component manufacturers recommend reducing maximum permissible operating pressure (load) when using biodegradable hydraulic fluids, to ensure no reduction in component life. After reviewing the available technical data on the hydraulic components fitted to the machinery being employed, a reduction in operating pressure to 80% of that permissible for mineral oil was considered prudent. The extraordinary costs that the contractor needed to consider in their bid included not only the expense of the fluid, and draining and flushing the hydraulic system to convert from mineral oil to vegetable oil and back again, but also the costs associated with derating the machinery. A reduction in system operating pressure means a reduction in actuator force. This means that a hydraulic excavator that has its operating pressure reduced by 20% will experience a 20% reduction in "break-out" force. The commercial implication of this meant that the contractor needed to cost the job allowing for the use of bigger machinery than they otherwise would have. Initiatives such as renewable energy and non-food uses for agricultural production have driven advances in biobased fluid technology. Once these fluids can compete with mineral oils on price and performance, their usage will increase and more data relating to hydraulic component life will become available. When this point is reached, biodegradable hydraulic fluids will no longer be relegated http://www.insidersecretstohydraulics.com/hydraulic-fluid-3.html (1 of 2) [5/10/2004 8:04:52 PM]

Hydraulic Fluid,Biodegradable Hydraulic Fluid

to special applications and the extraordinary costs associated with using them, as illustrated in the above example, will no longer apply.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-fluid-3.html (2 of 2) [5/10/2004 8:04:52 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

Hydrostatic transmissions - making sense of case drain flow - Part 1 One of our readers recently wrote to me regarding the following problem: "I tried one afternoon and evening to determine what was wrong with a hydrostatic transmission by monitoring case drain flow and was confused by the readings I was seeing. There was a flow meter in the transmission pump outlet and another in its case drain that always showed charge pump flow, even though the motor was bypassing profusely. The motor case drain went through the transmission pump case to tank."

What is a hydrostatic transmission? A hydrostatic transmission consists of a variable-displacement pump and a fixed or variable displacement motor, operating together in a closed circuit. In a closed circuit, fluid from the motor outlet flows directly to the pump inlet, without returning to the tank. As well as being variable, the output of the transmission pump can be reversed, so that both the direction and speed of motor rotation are controlled from within the pump. This eliminates the need for directional and flow (speed) control valves in the circuit. Because the pump and motor leak internally, which allows fluid to escape from the loop and drain back to the tank, a fixed-displacement pump called a charge pump is used to ensure that the loop remains full of fluid during normal operation. The charge pump is normally installed on the back of the transmission pump and has an output of at least 20% of the transmission pump's output. In practice, the charge pump not only keeps the loop full of fluid, it pressurizes the loop to between 110 and 360 PSI, depending on the transmission manufacturer. A simple charge pressure circuit comprises the charge pump, a relief valve and two check valves, through which the charge pump can replenish the transmission loop. Once the loop is charged to the pressure setting of the relief valve, the flow from the charge pump passes over the relief valve, through the case of the pump or motor or both, and back to tank.

http://www.insidersecretstohydraulics.com/hydrostatic-transmission.html (1 of 3) [5/10/2004 8:04:53 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

What is the significance of case drain flow? When a pump or motor is worn or damaged, internal leakage increases and therefore the flow available to do useful work decreases. This means that the condition of a pump or motor can be determined by measuring the flow from its case drain line (internal leakage) and expressing it as a percentage of its theoretical or design flow.

How does this apply to hydrostatic transmissions? When applying this technique to a hydrostatic transmission, charge pump flow must be considered. In most transmissions, the charge pump relief valve vents into the case of either the pump or the motor. This means that in the circuit described by our reader, where the motor case drain flushed through the transmission pump case to tank, you would expect to see the flow meter in the transmission pump case drain line reading design charge pump flow. Here's why: Say charge pump flow was 10 GPM, of which 4 GPM was leaking out of the loop through the motor's internals (case drain) and 2 GPM was leaking out of the loop through the pump's internals. The balance of 4 GPM must therefore be going over the charge relief - but still ends up in either the pump or motor case, depending on the location of the relief valve. In this particular circuit, because the motor case drain flushed through the transmission pump case to tank, you would expect to see the flow meter in the transmission pump case drain line reading the sum of these three flows (10 GPM). Before any meaningful conclusions can be drawn, the case in which the charge pump relief is venting (motor or pump) must be determined and the two case drain lines (motor and pump) must be isolated from each other. If the charge relief vents into the case of the pump, then it is possible to determine the condition of the motor by measuring its case drain flow, but not the pump. If the charge relief vents into the case of the motor, then it is possible to determine the condition of the pump by measuring its case drain flow, but not the motor. It is not possible to determine the condition of the component that has the charge relief valve venting into it because there is no way of telling what proportion of the total case drain flow is due to internal leakage - unless of course the charge relief can be vented externally while the test is conducted. While it is possible to do this on most transmissions, it's not usually a simple exercise. Using case drain flows to determine the condition of the components of a hydrostatic transmission, without a thorough understanding of closed circuits, can result in incorrect conclusions and the costly change-out of serviceable components.

http://www.insidersecretstohydraulics.com/hydrostatic-transmission.html (2 of 3) [5/10/2004 8:04:53 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydrostatic-transmission.html (3 of 3) [5/10/2004 8:04:53 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

Hydrostatic transmissions - making sense of case drain flow - Part 2 In my previous article, I outlined the theory and technique for using case drain flow to determine the condition of the components of a hydrostatic transmission. In response to this article, some readers thought that the function of the flushing valve warranted discussion, while others were still confused about the influence of the charge pump when determining case drain leakage. Let's consider flushing valves first.

What is a flushing valve? A closed circuit flushing valve (also called a transmission valve or replenishing valve) usually comprises a pilot operated directional valve and a low pressure relief valve. When the hydrostatic transmission is in neutral, the directional valve is centered and the gallery to the low pressure relief valve is blocked. When the transmission is operated in either forward or reverse, the high pressure side of the loop pilots the directional valve. This opens the low pressure side of the loop to the relief valve gallery.

What does a flushing valve do? In a closed circuit, fluid from the motor outlet flows directly to the pump inlet. This means that apart from losses through internal leakage, which are made up by the charge pump, the same fluid circulates continuously between pump and motor. If the transmission is heavily loaded, the fluid circulating in the loop can overheat. The function of the flushing valve is to positively exchange the fluid in the loop with that in the reservoir. A flushing valve is most effective when it is located at the motor, assuming the charge check valves are located in the transmission pump, as is the norm. When the hydrostatic transmission is in neutral, the flushing valve has no function and charge pressure is maintained by the charge relief valve in the transmission pump. When the transmission is operated in either forward or reverse, the flushing valve operates so that charge pressure in the low pressure side of the loop is maintained by

http://www.insidersecretstohydraulics.com/hydrostatic-transmission-2.html (1 of 2) [5/10/2004 8:04:55 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

the relief valve incorporated in the flushing valve. This relief valve is set around 30 psi lower than the charge pump relief valve located in the transmission pump. The effect of this is that cool fluid drawn from the reservoir by the charge pump, charges the low pressure side of the loop through the check valve located close to the transmission pump inlet. The volume of hot fluid leaving the motor outlet, that is not required to maintain charge pressure in the low pressure side of the loop, vents across the flushing valve relief into the case of the motor and back to tank, usually via the pump case.

How does a flushing valve influence the process of using case drain leakage to determine the condition of a transmission? The technique is the same as that outlined in the last issue. As explained above, if a flushing valve is fitted to a transmission, it acts as the charge pump relief valve once the transmission is operated in forward or reverse. So if the flushing valve vents into the case of the motor, then it is possible to determine the condition of the pump by measuring its case drain flow, but not the motor. If the flushing valve vents into the case of pump, then it is possible to determine the condition of the motor by measuring its case drain flow, but not the pump. This reinforces the point that using case drain flows to determine the condition of the components of a hydrostatic transmission, without a thorough understanding of the circuit in question, can result in incorrect conclusions and the costly change-out of serviceable components.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydrostatic-transmission-2.html (2 of 2) [5/10/2004 8:04:55 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

Hydrostatic transmissions - making sense of case drain flow - Part 3 In my previous articles, I described the technique for determining the condition of a hydrostatic transmission using case drain flow, and discussed the role and influence of a flushing valve when doing this. In response to these articles, some readers were still confused about the influence of the charge pump when determining case drain leakage. One reader held the view that, assuming the charge pump relief vents into the case of the motor and the motor case drain line is isolated from the pump, then transmission pump leakage is determined by subtracting charge pump flow from the total flow from the pump case. For example, if total charge pump flow was 10 GPM and the flowmeter in the pump case drain line was reading 15 GPM then transmission pump leakage would be 5 GPM (15 - 10 = 5). This is incorrect because it suggests that a hydrostatic transmission can leak more than the total available flow from its charge pump. It cannot. That is, it is impossible for the flow meter in the pump case drain line to read 15 GPM when the total available flow from the charge pump is only 10 GPM, as in the above example. The reason is simple. Because the function of the charge pump is to make up losses from the loop through internal leakage, if total losses exceed available charge pump flow, the transmission will cavitate. If in the above example, the transmission was leaking 5 GPM more than the total available flow from the charge pump, there would be a serious deficit of fluid in the loop. In practice, the transmission would destroy itself through cavitation before it got to this point. Let me explain this another way. Let's assume we have a transmission that has a volumetric efficiency of 100%, that is, the pump and motor have no internal leakage. The loop has a total volume of two gallons and is full of fluid. Because there is no internal leakage there is no need for a charge pump. The pump is stroked to maximum displacement, which circulates the two gallons of fluid in the loop at a rate of 50 GPM. Because it's a closed loop, with no leakage, the flow from pump to motor is 50 GPM and the flow from motor to pump is 50 GPM.

http://www.insidersecretstohydraulics.com/hydrostatic-transmission-3.html (1 of 2) [5/10/2004 8:04:57 PM]

Hydrostatic Transmission,Hydrostatic Transmissions

Now let's introduce internal leakage of 0.5 GPM in both pump and motor. The result is that, with no charge pump to replenish the loop, after one minute there will only be one gallon of fluid left in the loop (the other gallon will have leaked back to tank). Within a second of the transmission starting to leak, the transmission pump will start to cavitate and the severity of this cavitation will increase with each passing second until the transmission destroys itself. Now let's install a charge pump with a flow rate of 1 GPM in the circuit. Problem solved, temporarily at least. With 1 GPM leaking out of the loop and 1 GPM being replenished by the charge pump the status quo is maintained... until wear causes the internal leakage of the transmission to exceed 1 GPM. As you can see, it's not possible for the internal leakage of a hydrostatic transmission to exceed the flow rate of its charge pump. Charge pump flow rate is typically 20% of transmission pump flow rate. This means that volumetric efficiency can drop to 80% before the transmission will cavitate and destroy itself. The trick is to overhaul the transmission before this point is reached.

[Home]

Copyright 2003 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydrostatic-transmission-3.html (2 of 2) [5/10/2004 8:04:57 PM]

Temperature Shock,Thermal Shock

Temperature shock of hydraulic components and how to avoid it A client recently asked me to investigate and solve a recurring problem on a diving bell launch and recovery system. The system comprised of a hydraulic power unit, a bell winch, an umbilical winch and a guide-wire winch. To launch the bell, the guide-wire winch is used to lower a clump weight to the seabed (the guide wires prevent the bell from spinning during launch and recovery) and then the bell and its umbilical are launched using their respective winches. After the divers have finished their shift on the seabed (usually 6-8 hours) the bell and its umbilical are recovered, followed by the clump weight. The problem was occurring during recovery of the clump weight with the guide-wire winch. The motor on this winch was of radial piston design. When the winch was summoned to haul up the clump weight, the distributor shear pin (designed to prevent torque from being applied to the distributor valve), was frequently shearing, rendering the winch unserviceable. Once this pin has sheared, the distributor must be removed from the motor and the pin replaced. Apart from the obvious inconvenience, this was resulting in costly downtime. The cause of this problem was temperature shock.

What is temperature shock? When there is a significant difference between the temperature of a hydraulic component and the fluid being supplied to it, rapid, localized heating of the internal parts of the component can occur. This causes individual parts of the component to expand at different rates, resulting in interference between parts that normally have fine clearances.

How does this happen? Temperature shock occurs when part of a hydraulic circuit is operated for long enough for the fluid in the system to reach operating temperature, and then a previously idle part of the circuit is functioned. This results in hot fluid being delivered to cold components.

http://www.insidersecretstohydraulics.com/temperature-shock.html (1 of 2) [5/10/2004 8:04:58 PM]

Temperature Shock,Thermal Shock

In the example described above, due to the length of time between the launch of the bell and its recovery, the hydraulic system was at ambient temperature at the start of the recovery operation. By the time the bell and its umbilical had been hauled up 450 feet and were safely on deck, the hydraulic fluid was at operating temperature. But the guide-wire winch, which had been idle during this time, was still at ambient temperature. When the guide-wire winch was operated to recover the clump weight, the hot fluid entering the cold motor was causing the distributor valve to expand and bind in its housing, resulting in failure of the shear pin and rendering the motor unserviceable.

How can this be prevented? The solution to this problem and the fix in the above example is quite simple. To prevent temperature shock of hydraulic motors, the motor's case must be continuously 'flushed' (positive circulation of a relatively small volume of fluid through the case). This ensures that the motor is always at the same temperature as the fluid in the system.

[Home]

Copyright 2002 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/temperature-shock.html (2 of 2) [5/10/2004 8:04:58 PM]

Hydraulic valve power beyond or high pressure carry over

Configuring mobile hydraulic valves using power beyond I regularly receive questions from owners of mobile hydraulic equipment in relation to the correct installation of an additional directional control valve using the power beyond facility on an existing directional control valve.

What is power beyond? Power beyond - also called high-pressure carry over (HPCO), is a facility on a mobile hydraulic directional control valve that enables the pressure gallery to be isolated from the tank gallery and be carried over to an additional valve - usually another directional control valve. The valve being fitted must be sized to handle the rated flow from the pump. The arrangement of the power beyond facility varies with valve type and manufacturer. However the most common arrangement is a facility to install a threaded plug or sleeve that blocks the drilling between the pressure and tank galleries inside the valve. The power beyond port is then used to supply pump flow to the additional directional control valve. If the existing directional control valve has an alternative tank port, this allows the tank line from the additional valve to be connected to tank via the existing valve (Figures 1 & 2).

http://www.insidersecretstohydraulics.com/power-beyond.html (1 of 5) [5/10/2004 8:05:21 PM]

Hydraulic valve power beyond or high pressure carry over

Figure 1. Simplified line drawing showing pressure and tank galleries of a directional control valve (DCV) in open center arrangement.

http://www.insidersecretstohydraulics.com/power-beyond.html (2 of 5) [5/10/2004 8:05:21 PM]

Hydraulic valve power beyond or high pressure carry over

Figure 2. Connection of an additional open center DCV using the power beyond facility. Most mobile directional control valves can be made closed center by plugging the drilling between the pressure and tank galleries and leaving the power beyond port plugged (Figure 3). This means that if the existing valve is closed center, supplying pump flow to the additional valve only requires the connection of its pressure line to the existing valve's power beyond port (Figure 4).

http://www.insidersecretstohydraulics.com/power-beyond.html (3 of 5) [5/10/2004 8:05:21 PM]

Hydraulic valve power beyond or high pressure carry over

Figure 3. Simplified line drawing showing pressure and tank galleries of a DCV in closed center arrangement. It is important to note that if the existing valve is closed center, the power beyond plug or sleeve must be installed in the additional valve to make it closed center also(Figure 4).

http://www.insidersecretstohydraulics.com/power-beyond.html (4 of 5) [5/10/2004 8:05:21 PM]

Hydraulic valve power beyond or high pressure carry over

Figure 4. Connection of an additional closed center DCV using the power beyond facility.

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/power-beyond.html (5 of 5) [5/10/2004 8:05:21 PM]

Hydraulic Oil Leaks

The true cost of hydraulic oil leaks Hydraulic systems are often considered perennial consumers of oil and in turn, makeup fluid an inherent cost of operating hydraulic equipment. But what is the real cost of one or more "minor leaks" on your hydraulic equipment? To answer this question, the costs associated with all of the following factors need to be considered: ● ● ● ● ●

Make-up fluid. Clean-up. Disposal. Contaminant ingress. Safety.

Make-up fluid The cost of make-up fluid should be the most obvious cost of hydraulic system leaks. I say 'should be' because many hydraulic equipment users fail to consider the accumulative effect on the cost of one or more slow leaks over time. Consider a leak from a hydraulic fitting that produces six drops of oil per minute. Hardly worth your attention, right? If the volume of each drop was half a milliliter, over 24 hours the loss is nearly half a liter - perhaps not a significant amount. But over a month this equates to 15 liters and 180 liters over the course of a year. Assuming a fluid cost of $2 per liter, this "minor leak" is costing $360 per annum in make-up fluid alone.

Clean-up Where there are oil leaks there is almost always a clean-up cost to consider. Clean-up costs include: ● ●

●

labor; equipment required to empty sumps and drip trays, and degrease machine surfaces; and consumables such as detergents and absorbent material.

Assuming it costs $10 per week in labor, equipment and consumables to clean up the

http://www.insidersecretstohydraulics.com/hydraulic-oil-leaks.html (1 of 3) [5/10/2004 8:05:23 PM]

Hydraulic Oil Leaks

minor leak discussed above, the annual clean-up bill totals more than $500.

Disposal I can remember a time, not so long ago, when waste oil companies used to pay for the privilege of emptying waste hydraulic oil tanks. These days they bill you for the privilege. Environmentally acceptable disposal of waste oil and absorbent material containing waste oil costs money. Assuming a disposal cost of $0.60 per liter, the annual disposal costs attributable to the minor leak discussed above amounts to $110.

Contaminant ingress Where oil leaks out, contaminants such as air, particles and water can get in. Costs to consider here include: ●

● ●

hydraulic component damage and fluid degradation as a result of contaminant ingress; hydraulic system reliability problems; and removal of ingested contaminants.

Safety In many situations, oil leaks can pose a safety hazard. Like the costs associated with contaminant ingress, the costs associated with the safety risk posed by oil leaks are difficult to quantify - short of a lost time accident actually occurring. In addition, the cost of minimizing the safety risk can be obscured. An example would be more frequent clean-up than may otherwise be required. This hides what is essentially a safety cost in clean-up expenses.

Conclusion The annual cost of one slow leak, similar to that discussed above, amounts to nearly $1,000 per year in make-up fluid, clean-up and disposal costs alone. If you have multiple pieces of hydraulic equipment with several leaks on each one, the accumulative cost over an extended period of time should alarm you. Inspect your hydraulic equipment today and tag all leaks for corrective action during the next available maintenance outage. It could save you a lot of money!

http://www.insidersecretstohydraulics.com/hydraulic-oil-leaks.html (2 of 3) [5/10/2004 8:05:23 PM]

Hydraulic Oil Leaks

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/hydraulic-oil-leaks.html (3 of 3) [5/10/2004 8:05:23 PM]

Símbolo Hidráulico

El Valor de un Sencillo Símbolo Hidráulico Normalmente me encuentro involucrado en el analisis y solucion de problemas relacionados con sistemas hidraulicos. En estas situaciones, hay dos pasos que siempre sigo, antes de comenzar a realizar pruebas o ajustes. El primero, es realizar una inspeccion visual del sistema hidraulico, revisando todas aquellas cosas obvias que pudiesen estar causando el problema ( nunca hay que sobre-estimar lo obvio ). El segundo, es solicitar el diagrama hidraulico del sistema que se va a analizar.

Que es un diagrama hidraulico Un diagrama hidraulico es un dibujo a base de trazos lineales sencillos y simbolos hidraulicos que nos indica el tipo de componentes de los que consta el sistema hidraulico y la forma en la que estan interconectados entre si.

Que es lo que hace valioso a un diagrama hidraulico Un diagrama hidraulico es un “mapa” que nos guia por el sistema hidraulico que estamos analizando y para un tecnico capacitado en la lectura e interpretacion de los simbolos hidraulicos, es una herramienta muy valiosa para identificar posibles causas de algun problema, ahorrandose enorme cantidad de tiempo y dinero, al momento de atacar y solucionar una falla en un sistema hidraulico. Si el diagrama hidraulico no se encuentra disponible, el tecnico tendra que rastrear el sistema hidraulico e indetificar uno por uno a los componentes del mismo, con objeto de saber su funcion y poder asi aislar las posibles causas del problema. Este procedimiento puede llevarse bastante tiempo, dependiendo de lo complejo del sistema. Peor aun, si el sistema hidraulico incluye uno o varios blocks manifold, estos tendran que ser desmontados del sistema y desmantelados, con objeto de analizar lo que esta sucediendo en el interior de los mismos. Por otra parte, muchos de los componentes en maquinaria con varios años de servicio, no tienen identificacion, por lo que resulta dificil saber que tipo de valvula es, aun en el caso de que se disponga de catalogos del fabricante de los equipos hidraulicos. Si se desconoce la funcion de un componente en un sistema hidraulico, sera muy

http://www.insidersecretstohydraulics.com/simbolo-hidraulico.html (1 of 2) [5/10/2004 8:05:25 PM]

Símbolo Hidráulico

dificil si no es que imposible, descartarlo como posible causa del problema que estamos tratando de resolver. Por el contrario, si se dispone de aquel “sencillo simbolo hidraulico” nos evitaremos la necesidad de realizar un procedimiento de “ingenieria inversa” al circuito hidraulico, para poder comprenderlo y resolver sus problemas.

Donde se encuentran todos los diagramas hidraulicos Pues bien, la realidad es que normalmente no se dispone del diagrama hidraulico de la maquina que hemos sido llamados a reparar; si bien esto le causa un serio contratiempo al tecnico encargado de resolver el problema, sera el dueño de la maquinaria quien realmente pague por ello, con tiempo muerto de produccion, mientras que se resuelve el problema. Entonces viene la pregunta de en donde se encuentran todos los diagramas hidraulicos. Se perdieron o se colocaron en el lugar equivocado, o bien los diagramas no fueron entregados al nuevo dueño de la maquinaria si esta es de segunda mano. Se han dado casos inclusive, en que al dueño de una maquinaria nueva no se le entreguen diagramas hidraulicos y esto pase inadvertido, debido a la poca importancia que se le da a los circuitos hidraulicos por parte de quien va a operar una maquinaria que incluya este tipo de sistemas.

Conclusion Si usted es el responsable de la operacion o del mantenimiento de equipo hidraulico y no tiene a la mano los diagramas hidraulicos de los sistemas instalados en la maquinaria, trate de obtenerlos antes de que los llegue a necesitar. Asegurese ademas de que cuando adquiera una nueva maquina, le sea proporcionada toda la informacion de los equipos hidraulicos instalados y el diagrama hidraulico correspondiente. Esto le ahorrara dinero a la larga. Traducción del artículo: The value of the humble hydraulic symbol Traduccion: Ing. Miguel Mota Bush, techniforum.com

[Home]

Copyright 2004 -- Insider Secrets to Hydraulics

http://www.insidersecretstohydraulics.com/simbolo-hidraulico.html (2 of 2) [5/10/2004 8:05:25 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_3.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_3.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_3.pdf [5/10/2004 8:24:16 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_4.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_4.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_4.pdf [5/10/2004 8:24:36 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_5.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_5.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_5.pdf [5/10/2004 8:25:49 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_11.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_11.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_11.pdf [5/10/2004 8:26:16 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_6.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_6.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_6.pdf [5/10/2004 8:26:54 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_7.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_7.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_7.pdf [5/10/2004 8:28:17 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_9.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_9.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_9.pdf [5/10/2004 8:29:25 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_10.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_10.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_10.pdf [5/10/2004 8:29:49 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_13.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_13.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_13.pdf [5/10/2004 8:32:56 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_8.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_8.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_8.pdf [5/10/2004 8:33:12 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_12.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_12.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_12.pdf [5/10/2004 8:34:53 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_15.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_15.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_15.pdf [5/10/2004 8:36:47 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_14.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_14.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_14.pdf [5/10/2004 8:37:04 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_16.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_16.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_16.pdf [5/10/2004 8:37:48 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_26.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_26.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_26.pdf [5/10/2004 8:38:09 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_19.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_19.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_19.pdf [5/10/2004 8:44:53 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_22.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_22.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_22.pdf [5/10/2004 8:45:20 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_21.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_21.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_21.pdf [5/10/2004 8:45:37 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_20.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_20.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_20.pdf [5/10/2004 8:46:03 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_17.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_17.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_17.pdf [5/10/2004 8:56:19 PM]

http://www.hydraulicsupermarket.com/upload/db_documents_doc_18.pdf

Embedded Secure Document The file http://www.hydraulicsupermarket.com/upload/db_documents_doc_18.pdf is a secure document that has been embedded in this document. Double click the pushpin to view.

http://www.hydraulicsupermarket.com/upload/db_documents_doc_18.pdf [5/10/2004 8:59:05 PM]